answersLogoWhite

0

The beta cut off frequency is the frequency at which the current amplification of an amplifier transistor drops to three decibels below its value at 1 kilohertz. This is used in electronic engineering.

User Avatar

Wiki User

10y ago

What else can I help you with?

Continue Learning about Electrical Engineering

How does a capacitor act as a filter?

The cutoff frequency of filter depends upon the value of capacitor and resistance. Therefore, below cutoff frequency or above this frequency, capacitor allow to pass all other frequencies.


What is band rate?

ANSWERED MY MUHAMMAD WALEED SHAIKH first of all we have to know that about band,so band is range of frequency which we have selected for example:we have a low pas filter it frequency always started from initial or 0 HZ upto cutoff frequency and here remember that cutoff frequency we will have to select after cutoff signal is rapidly down now about band rate so your signal is band at certain rate is called band rate.


Why does the existence of a cutoff frequency in the photoelectric effect favor a particle theory of light rather than a wave theory?

According to the wave theory, light of any frequency can cause electrons to be ejected as long as the light is intense enough. A higher intensity corresponds to a greater electric field magnitude and more energy. Therefore, there should be no frequency below which the photoelectric effect does not occur. According to the particle theory, however, each photon carries an amount of energy that depends upon its frequency. Increasing the intensity of the light increases the number of photons but does not increase the energy of the individual photons. The cutoff frequency is that frequency at which the energy of the photon equals the work function. If the frequency of the incoming light is below the cutoff, the electrons will not be ejected because no individual photon has enough energy to impart to an electron.


Relation between cutoff frequency and bandwidth?

The relation between cut off frequency (fc) and band width is as follows: fc=Q*B.W where Q=(fL*fH)^1/2/(fH-fL) Q is quality factor. fL is low frequency. fH is high frequency.


High pass RC circuit?

Hi pass says it passes higher frequency signals and blocks lower pass signals. This isn't typically a hard cutoff point but the lower frequency signals get attenuated over a frequency range. The R stands for resistance and C for capacitance such that these components are used to create the pass band for the circuit.

Related Questions

How does a capacitor act as a filter?

The cutoff frequency of filter depends upon the value of capacitor and resistance. Therefore, below cutoff frequency or above this frequency, capacitor allow to pass all other frequencies.


How does a capacitor acts as a filter?

The cutoff frequency of filter depends upon the value of capacitor and resistance. Therefore, below cutoff frequency or above this frequency, capacitor allow to pass all other frequencies.


The attenuation in wave guides near the cutoff frequency is?

zero


What is the significance of the cutoff frequency in an RL circuit?

The cutoff frequency in an RL circuit is the frequency at which the output signal power is half of the maximum power. It is significant because it determines the range of frequencies that can pass through the circuit effectively, affecting the overall performance and functionality of the circuit.


What is the -3dB cutoff frequency?

A: It is a standard statement to signify that the amplitude is one half.


What is band rate?

ANSWERED MY MUHAMMAD WALEED SHAIKH first of all we have to know that about band,so band is range of frequency which we have selected for example:we have a low pas filter it frequency always started from initial or 0 HZ upto cutoff frequency and here remember that cutoff frequency we will have to select after cutoff signal is rapidly down now about band rate so your signal is band at certain rate is called band rate.


How value of c is calculated in an RC filter for a given value of r?

Time constant = R C C = time constant/R R = time constant/C When used as a filter, Cutoff frequency = 1 / (2 pi) R C R = 1 / (2 pi) (cutoff frequency) ( C ) C = 1 / (2 pi) (cutoff frequency) ( R )


What is the lowpass filter cutoff frequency that must be used to decimate to reduce the sampling rate from 8kHz to 4kHz?

2kHz - That's the nyquist frequency at a sample frequency of 4kHz.


What do you mean by 3 dB cutoff frequency?

3db frequency is the frequency at which the value in the graph is reduced by 3db level It's also known as the half-power point.


How do you convert a beta probability density function to a beta frequency distribution?

probability density distribution


What is the frequency of a beta particles?

The frequency of beta particles corresponds to the energy of the electrons or positrons emitted during beta decay. These particles can have a wide range of frequencies depending on the specific isotope and the decay process involved.


Why gain increases in low frequency region in BJT?

Because Beta (current gain) in a transistor is inversely proportional to frequency. Hence it increases as frequency decreases. Also the ac voltage gain is directly proportional to Beta.