answersLogoWhite

0

Crossover distortion is a type of distortion which is caused by switching between devices driving a load, most often when the devices (such as a transistor) are matched. It is most commonly seen in complementary, or "push-pull", Class-B amplifier stages, although it is occasionally seen in other types of circuits as well

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Electrical Engineering

What is Class B push-pull amplifier?

When we get amplifier output current for 180 degrees of input. then it's called B class amplifier. In a push pull class B amplifier one of the two power transistors or other amplifying elements handles the positive half of the waveform and the other element handles the negative half of the waveform. In practice, push pull audio amplifiers are usually class AB; each power transistor handles slightly more than 180 degrees of input. This minimizes distortion (crossover distortion) when one of the two transistors ceases output and the other takes over.


What is an AF amplifier?

AF means audio frequency. Audio Amplifiers can be subgrouped as voltage amplifiers (or pre-amplifiers) and power amplifiers. The voltage amplifier will raise the level of level of the output of a microphone from say 1 mV to 500mV or 1V. The power amplifier will be the interface between this and the load, which is a speaker. The resistance of the speaker is often 4 ohm or 8 ohm. You cannot have a speaker with 1k as resistance! As such to get say 8W output, an amplifier providing 8V will have to pump 1 amp into an 8 ohm speaker. Thus power amplifiers will have to drive a lot of current into the load. Voltage amplifiers cannot do this. A power amplifier sometimes just has unity voltage gain, but has ability to drive a lot of current into the load. Typical power amplifiers are operated in class B, where for 50% of the signal swing, one transistor provides current, and for the other 50%, the other transistor in a class B provides current into load. Class B amplifiers have cross over distortion, But this can be overcome by pre-biasing, or making the stage operate as class AB. The power amplifiers can also be used to power low resistance loads such as a step up transformer.


What is meant by the term large signal amplifier?

power amplifiers are the amplifier which raise the power levels of the signal.the power amplifier may also defined as a device which converts dc power to ac power and whose action is controlled by the ac input signal. Power amplifiers are also known as "LARGE SIGNAL AMPLIFIER".the term large signal arises because they use large part of load line for their operation,but the small signal amplifiers are use only 10% load line for their operation.


What is amplifier and types of amplifiers?

Amplifiers are electronic device that responds to a small input signal (voltage, current, or power) and delivers a larger output signal.


What types of applications are valve amplifiers used for?

A quick search of this incredible question brought fourth some greater insight into the matter. It turns out the applications valve amplifiers are used for vary from guitar amplifiers, satellite transponders, audiophile stereo amplifiers, military applications and high power radio and UHF television transmitters.

Related Questions

Do professional power amplifiers work well in home audio?

It will if you have proffessioanal equipment to go with it ( speakers ) the amp has to be around the same wattage of the speaker or you will get distortion


What has the author James N Jameson written?

James N. Jameson has written: 'Low distortion transistor power amplifiers' -- subject(s): Electronics


What is Class B push-pull amplifier?

When we get amplifier output current for 180 degrees of input. then it's called B class amplifier. In a push pull class B amplifier one of the two power transistors or other amplifying elements handles the positive half of the waveform and the other element handles the negative half of the waveform. In practice, push pull audio amplifiers are usually class AB; each power transistor handles slightly more than 180 degrees of input. This minimizes distortion (crossover distortion) when one of the two transistors ceases output and the other takes over.


What is a class c amplifier?

A class A amplifier is an amplifier where the bias current in all amplifier stages, including the power amplifier, always exceeds the maximum output current. This leads to a very high energy consumption (and cooling might become a problem), but eliminates crossover distortions. Typical commercial amplifiers are what is called class A/B amplifiers, meaning, they would use a pretty high bias current to eliminate crossover distortions, but the bias current would still be less than the maximum output current to reduce the energy waste and cooling problems associated with pure class A amplifiers.


Is there a Beyblade and power rangers crossover?

No, there is no crossover between Beyblade and the Power Rangers.


What is Class b power amplifier?

When we get amplifier output current for 180 degrees of input. then it's called B class amplifier. In a push pull class B amplifier one of the two power transistors or other amplifying elements handles the positive half of the waveform and the other element handles the negative half of the waveform. In practice, push pull audio amplifiers are usually class AB; each power transistor handles slightly more than 180 degrees of input. This minimizes distortion (crossover distortion) when one of the two transistors ceases output and the other takes over.


What is bi-amping speaker?

Bi-amping means using a crossover filter to separate high and low frequencies, and sending them to two separate amplifiers, which power the high- and low-frequency drivers in the speaker separately. This is in contrast to the use of a single amp and a passive crossover filter. The primary advantage to bi-amping is lower distortion, due to a) more accurate, active crossover circuitry, b) better impedance matching between the amp and the driver, c) no passive components between the amp and the drivers, and d) no electrical interaction between the drivers. The frequency response is improved, also, due to better phase matching between drivers in the crossover range.


What are some top hi-fi amplifiers made in Germany, known for their quality and craftsmanship?

Hi-fi power amplifiers made in Germany are renowned for their precision and exceptional sound quality. These amplifiers play a crucial role in audio systems by taking low-level signals and amplifying them to match the power requirements of the speakers, ensuring clear, distortion-free sound. With their efficient design, German-made power amplifiers elevate listening experiences in both home theaters and professional setups, providing high-level sound reproduction with outstanding fidelity and performance.


What has the author Steve C Cripps written?

Steve C. Cripps has written: 'RF power amplifiers for wireless communications' -- subject(s): Amplifiers, Radio frequency, Power amplifiers, Radio frequency Amplifiers


What is an AF amplifier?

AF means audio frequency. Audio Amplifiers can be subgrouped as voltage amplifiers (or pre-amplifiers) and power amplifiers. The voltage amplifier will raise the level of level of the output of a microphone from say 1 mV to 500mV or 1V. The power amplifier will be the interface between this and the load, which is a speaker. The resistance of the speaker is often 4 ohm or 8 ohm. You cannot have a speaker with 1k as resistance! As such to get say 8W output, an amplifier providing 8V will have to pump 1 amp into an 8 ohm speaker. Thus power amplifiers will have to drive a lot of current into the load. Voltage amplifiers cannot do this. A power amplifier sometimes just has unity voltage gain, but has ability to drive a lot of current into the load. Typical power amplifiers are operated in class B, where for 50% of the signal swing, one transistor provides current, and for the other 50%, the other transistor in a class B provides current into load. Class B amplifiers have cross over distortion, But this can be overcome by pre-biasing, or making the stage operate as class AB. The power amplifiers can also be used to power low resistance loads such as a step up transformer.


Does SIC 3663 cover makers of RF power amplifiers?

SIC 3663 covers makers of RF power amplifiers


What is meant by the term large signal amplifier?

power amplifiers are the amplifier which raise the power levels of the signal.the power amplifier may also defined as a device which converts dc power to ac power and whose action is controlled by the ac input signal. Power amplifiers are also known as "LARGE SIGNAL AMPLIFIER".the term large signal arises because they use large part of load line for their operation,but the small signal amplifiers are use only 10% load line for their operation.