answersLogoWhite

0

A clipper is a device designed to prevent the output of a circuit from exceeding a predetermined voltage level without distorting the remaining part of the applied waveform.

A clipping circuit consists of linear elements like resistors and non-linear elements like junction diodes or transistors but it does not contain energy-storage elements like capacitors. Clipping circuits are used to select for purposes of transmission, that part of a signal wave form which lies above or below a certain reference voltage level.

In half wave rectification of a single-phase supply, either the positive or negative half of the AC wave is passed, while the other half is blocked. Because only one half of the input waveform reaches the output, mean voltage is lower. Half-wave rectification requires a single diode in a single-phase supply , or three in a three-phase supply. Rectifiers yield a unidirectional but pulsating direct current; half-wave rectifiers produce far more ripple than full-wave rectifiers, and much more filtering is needed to eliminate harmonics of the AC frequency from the output.

Half-wave rectifier

The no-load output DC voltage of an ideal half wave rectifier for a sinusoidal input voltage is:

Where:

Vdc, Vav - the DC or average output voltage,Vpeak, the peak value of the phase input voltages,Vrms, the root-mean-square value of output voltage.

User Avatar

Wiki User

9y ago

What else can I help you with?

Related Questions

What is the difference between human and dog clippers?

nothing realy but dog clippers are a bit sharper to get more hair off HOPE this helps


What is the difference between oster titan clipper vs oster classic 76?

To be honest the only difference between these two clippers are the prices.


Are dog clippers and hair clippers he the same?

They are practically the same yes. The only difference between clippers most of the time, is whether they were designed to be used professionally (heavy-duty), or if they were designed for minimum at home use.


What is difference between single phase and three phase rectifiers?

Single phase rectifiers are suitable to power loads of up to only about 15 kW. For higher power demands, three phase rectifiers are preferred for the following reasons: Higher dc voltage, better TUF, better input power factor, less ripple content in the output current - therefore giving better load performance and a smaller size of filter circuit parameters because of the higher ripple frequency.


What are the differecne between chopper and rectifiers?

for controlling a motor if it is in a important application we use rectifiers because the ripple factor of the chopper is very high in comparison with choppers


What is the difference between an alternator and a generater?

A generator generates Direct current electricity An Alternator generate alternating current In a car this current is run through rectifiers or diodes to convert it into DC.


What is the difference between uncontrolled and controlled rectifierWhich is advantageous and why?

Uncontrolled rectifiers, such as diode rectifiers, allow current to flow in one direction but do not control the output voltage or current, leading to less efficiency and limited applications. In contrast, controlled rectifiers, like thyristor-based systems, can regulate the output by adjusting the firing angle, allowing for better voltage and current control. Controlled rectifiers are generally more advantageous for applications requiring precise power management, such as in motor speed control and power supplies, due to their ability to optimize performance and efficiency.


What are Similarities between controlled and uncontrolled rectifiers?

Both controlled and uncontrolled rectifiers convert alternating current (AC) to direct current (DC). They share similar circuit configurations, often utilizing diodes or thyristors for the conversion process. Additionally, both types are used in various applications, such as power supplies and motor drives. However, the key difference lies in the ability of controlled rectifiers to regulate output voltage and current through control signals, whereas uncontrolled rectifiers provide a fixed output based solely on the input AC waveform.


What is the average price for a set of Remington hair clippers?

The average price for a set of Remington hair clippers is between $30 and $40. You can purchase Remington hair clippers online from retailers such as Amazon.


What is the difference between limiting and clamping circuit?

A diode-clipping circuit is used to skip some portion of the signal (e.g. the half way/full way rectifiers rectify the '-ve' or '+ve' part of the signal). A diode-clamping circuit is used to add some signals to the original signal.


Which hair clippers are the best between Andis Improved Fade Master Andis Phat Fade master or Andis MLX Also wich trimmer is better Andis T-Outliner 2 or Wahl 5 Star Detailer?

The best hair clippers are the Andis Improved Master Clippers.


What kind of oil is used on clippers?

Clipper oil, typically a lightweight mineral oil or specially formulated clipper lubricant, is used on clippers to ensure smooth operation and prevent overheating. It reduces friction between blades, prolongs the lifespan of the clippers, and helps achieve a clean, precise cut. It's important to use oil specifically designed for clippers, as other oils may not provide the necessary properties or could damage the equipment.