0
What else can I help you with?
What is the function of the capacitor in the fluorescent lamp?
The capacitor in a fluorescent lamp is primarily used to improve the power factor of the lamp's circuit. It helps to correct the phase difference between the voltage and current in the circuit, which can improve the overall efficiency of the lamp. Additionally, the capacitor helps to stabilize the voltage across the lamp, reducing flickering and ensuring a more consistent light output.
What is the effect on the supply current if the capacitor is removed from a fluorescent fitting?
Removing the capacitor from a fluorescent fitting can lead to an increase in supply current. The capacitor is typically used for power factor correction, helping to reduce the reactive power in the circuit. Without it, the power factor may decrease, resulting in higher current draw from the supply to maintain the same level of performance. This can also lead to increased energy losses and potential overheating in the electrical system.
Why capacitor bank not connected across Diesel generator power supply?
I dont know.... may be due to save money
What happens when a capacitor is connected to a dc supply?
is it ? are you sure ? but i know so many circuit where capacitor is connected with ac supply . still , if u connected a capacitor to dc supply , then : 1. if it is in SERIES with the dc supply , it will block all the dc current as capacitor provides infinite resistance to dc current . application : where u want to block dc current.(simple high pass filter) 2. if it is in PARALLEL with the dc supply , it will not block dc current , but if any ac current comes out from the supply , the ac current will go through the capacitor , as capacitor provides small resistance to ac current. application : a) where u want to block ac current.(simple low pass filter) b) to filter the noise (ac components) of dc supply.
What is capacitor smoothing?
A Smoothing Capacitor is a capacitor which helps to smooth out fluctuations that may exist on a power supply line.
What is the function of the capacitor in the fluorescent lamp?
The capacitor in a fluorescent lamp is primarily used to improve the power factor of the lamp's circuit. It helps to correct the phase difference between the voltage and current in the circuit, which can improve the overall efficiency of the lamp. Additionally, the capacitor helps to stabilize the voltage across the lamp, reducing flickering and ensuring a more consistent light output.
What is the effect on the supply current if the capacitor is removed from a fluorescent fitting?
Removing the capacitor from a fluorescent fitting can lead to an increase in supply current. The capacitor is typically used for power factor correction, helping to reduce the reactive power in the circuit. Without it, the power factor may decrease, resulting in higher current draw from the supply to maintain the same level of performance. This can also lead to increased energy losses and potential overheating in the electrical system.
What type of function of capacitor in dc power supply?
It filters ac to pure dc
Will voltage drop across a capacitor?
basically a capacitor will charge to the input DC level however it will mathematically never happen since capacitors charge at a certain rate the voltage drop across a capacitor will follow the R C time constant or 63% of the applied voltage for a unit time.AnswerIn the case of an a.c. supply, yes, there will be a voltage drop across a capacitor. In the case of an 'ideal' capacitor, this will be the product of the load current and the capacitive reactance of the capacitor.
Why capacitor bank not connected across Diesel generator power supply?
I dont know.... may be due to save money
Can a capacitor hold open an ac relay?
No, because as soon as a load is connected across a capacitor it will discharge. You need a continuous voltage supply across the coil of a relay to keep it energized. Yes. A large capacitor, 10000 mfd, can hold open a small relay for a few seconds, plus or minus, depending on your varibles.
When a capacitor fully charged?
A capacitor is fully charged when the voltage across its plates equals the voltage of the power supply it is connected to, resulting in no current flow between the plates. At this point, the electric field within the capacitor is stable, and it holds a maximum amount of stored energy based on its capacitance and the voltage. Any further increase in voltage or connection to a higher voltage supply will not occur unless the capacitor is discharged or disconnected.
What is a smoothing capacitor?
A Smoothing Capacitor is a capacitor which helps to smooth out fluctuations that may exist on a power supply line.
Does a fluorescent ballast work in a DC V supply?
No, fluorescent ballasts are designed to work with AC voltage supplies. They require the alternating current to function properly and cannot operate on a direct current (DC) power source.
Why is a capacitor used in a starter?
A capacitor is used to reduce the arcing when the ignition circuit's contacts open and close.A longer answerTo be answered fully, this question needs to give more information:Is the question asking about a starter for an aero engine or a ship's engine, or for the engine on a car, truck or other vehicle?Or is the question asking about the starter for a fluorescent light fitting?Answer for a fluorescent light fixture's starterA capacitor is a device which absorbs and stores energy in the form of an electric field.When we switch on the light, the fluorescent tube initially requires more energy than is required for when it is continually running.This is because the tube's two filaments - one at each end of the tube - have to be supplied with current to give them enough energy to heat up and glow. Their extra heat makes an arc flash across the tube, between the two filaments.The arc will then continue running across the tube once the filaments have been disconnected from the power source. *** (See Note below.)After the arc has started across the tube, a switch inside the starter must open to break the supply of current to the filaments.Without a capacitor, a secondary arc would start across the open contacts of the switch inside the starter and that arc would quickly cause those contacts to burn away. The capacitor absorbs the energy which would otherwise start that secondary arc to glow. That is why a capacitor has to be used in the starter for a fluorescent lamp.*** NoteAs part of the lighting fixture there has to be a special inductance coil - called a "choke" - that is wired in series with the fluorescent tube.The choke's purpose is to limit the amount of current drawn by the arc whilst the tube is lit up. Without the choke the arc would act like a short circuit and would cause the circuit breaker or fuse protecting the lighting circuit to trip or blow in order to cut off the supply of current.
What happens when a capacitor is connected to a dc supply?
is it ? are you sure ? but i know so many circuit where capacitor is connected with ac supply . still , if u connected a capacitor to dc supply , then : 1. if it is in SERIES with the dc supply , it will block all the dc current as capacitor provides infinite resistance to dc current . application : where u want to block dc current.(simple high pass filter) 2. if it is in PARALLEL with the dc supply , it will not block dc current , but if any ac current comes out from the supply , the ac current will go through the capacitor , as capacitor provides small resistance to ac current. application : a) where u want to block ac current.(simple low pass filter) b) to filter the noise (ac components) of dc supply.
A series LCR circuit consisting of R10 ohms and impedence 20 ohms is connected across an ac supply of 200 v rms The rms voltage across the capacitor is?
16.32 volts
