0
What else can I help you with?
What size wire should be use for connecting a 110 kw motor over a distance of 108 meters?
This is a voltage drop question. To answer this question a voltage must be given.
What is power cable size for 1 kw 1 phase motor over 500 meters?
It depends on the voltage that the motor needs, because a higher voltage requires less current for a given amount of power. Also a higher voltage can tolerate a higher voltage drop. So there are two things that lead to a thinner wire when the voltage is higher.
What size cable for 50 amps 3 phase for 650 meters length?
70mm 4core copper cable
What are the reasons of getting different results using different sets of multimeters and probes for the same supply voltage?
Incorrectly calibrated meters.
What AWG wire size will be required to carry 20 Amperes for 6 meters?
Since you're only going 6 meters as your distance the voltage drop will not be a significant issue and you can use #12 AWG that is rated for 20 Amps
The scale for a drawing is 1 centimeter 5 meters Make a scale drawing that measures 20 meters by 15 meters?
To create a scale drawing that measures 20 meters by 15 meters using a scale of 1 cm to 5 meters, you would need to draw a rectangle that is 4 cm by 3 cm. Each centimeter on the drawing represents 5 meters in real life, so 4 cm would represent 20 meters and 3 cm would represent 15 meters.
A sentence with voltage in it?
Voltage can kill a person even if you are only meters away.
How much voltage drop will be in 6 meter length of 16 mm² copper wire for 40 Amp load?
The voltage drop in a 6-meter length of 16 mm² copper wire carrying a 40 Amp load can be calculated using Ohm's Law and the wire's resistance. Copper wire has a resistance of about 0.000133 ohms per meter. The voltage drop can be found using the formula Voltage Drop = Current x Resistance x Length. Therefore, the voltage drop in this scenario would be approximately 0.32 volts.
Where would you place the meters to measure voltage?
any where across where you think there is voltage present
What are square meters and meters?
A meter is a unit of metric measurement. A square meter is like drawing 4 meters to make a square.
Why do you put the meters in the high voltage side in the short circuit test?
in the short circuit test we applied supply voltage on L.V side and short circuit the H.V side and connect the ammeter in H.V circuit to measure the short circuit current. with the help of s.c test we measure the copper losses in the transformers.
The height of the CN Tower is 550 meters what is the height of the Tower in a scale drawing if the scale is 1 to 11000?
Well, honey, if the CN Tower is 550 meters tall in real life and you're using a scale of 1:11000 on your drawing, then you just divide 550 by 11000 to get the height in the drawing. So, the height of the CN Tower in the scale drawing would be 0.05 meters, or 5 centimeters. Hope that helps, sugar!
What is the speed of light in copper?
The speed of light in copper is approximately 1.97 x 108 meters per second.
What size cable for single phase 240volt carrying 65amps over 150 meters?
A 2/0 AWG copper conductor will limit the voltage drop to 3% or less when supplying 65 amps for 150 metres on a 240 volt system.
What is the use of a volt meters as a laboratory tool?
To measure voltages and voltage drops
The speed of sound through oxygen at 0 and Acirc and degC is 316 meters per second. The speed of sound through solid copper is 5010 meters per second.?
No. The speed of sound in copper is well below that.
When It is required to calculate average voltage and when RMS voltage?
It is usually required in electrical examinations to make calculations. Simple answer to a complicated calculation. Remember, take peak to peak voltage and multiply by .707, the result being average voltage. This is the voltage that electrical test meters read.
