answersLogoWhite

0

What else can I help you with?

Continue Learning about Electrical Engineering

How do you read 208 volts single phace circuit?

All voltage reading are usually read with a volt meter. This volt meter can be a hand held unit like electricians use.


As you add more lamps to a parallel circuit what will the ammeter reading do?

If the amp meter is in series ahead of the first parallel branch of lamps the meter will read an increase in current.


How does the loading effect of a voltmeter in a high-rsistance circuit compare to the loading effect in a low-resistance circult?

The voltmeter has an internal resistance, which should be as high as possible. As this resistance draws current from the circuit under test, it will affect circuit operation. This is more pronounced in a high impedance circuit because the current drawn flows through higher resistances.


What is transformer open circuit test?

An open-circuit test measures a transformer's iron losses. With no current flowing in the secondary windings, and only a tiny 'magnetising' current flowing in the primary windings, there is no significant energy lost due to the resistance of the winding conductors. So a wattmeter attached to the primary of the transformer will not read any 'copper losses', only the 'iron losses' that occur in the core.


How do you measure IGBT?

Digital multi-meter (DMM) test procedure:Equipment Requirement - DMM with diode check mode and battery voltage less than 20V. (Typical units using 9V battery are OK).Collector-Emitter Junction test: With the module out of circuit remove the conductive foam and short the gate to emitter.With DMM in diode check mode, the collector to emitter should give a normal diode reading with positive on the emitter and negative on the collector.The DMM should read open or infinite with positive on the collector and negative on the emitter. Damaged IGBTs may test as shorted in both positive and negative directions, open in both directions, or resistive in both directions.Gate Oxide test: With the DMM in resistance mode the resistance from gate to collector and gate to emitter should read infinite on a good device. A damaged device may be shorted or have resistive leakage from gate to collector and/or emitter.

Related Questions

If you read infinity on a analog meter what would this mean?

In the ohms position that means an open circuit.


How do you find shorts and opens in an electrical circuit in multimeter?

An open circuit essentially has an infinite resistance. It is shown on digital multimeter as OL. (Open Line) A short circuit should read zero, or nearly zero, depending on the accuracy of the meter.


How do you read 277 volts on meter?

To read 277 volts on a meter, simply ensure the meter is set to the appropriate voltage scale (typically AC). Then, connect the meter leads to the circuit or outlet you are measuring. The display should show the voltage reading, which in this case would be 277 volts. Be sure to take appropriate safety precautions when working with electricity.


How do you read 208 volts single phace circuit?

All voltage reading are usually read with a volt meter. This volt meter can be a hand held unit like electricians use.


What does the reading on a ammeter say when the switch is open?

An open switch in a circuit will stop all current flow so the ammeter should read zero amps.


What should the battery meter read on a 95 Chevrolet blazer?

Should read 14 volts.


What should the volt meter gauge read in a 1993 jeep yj?

what should the volt meter guage read in my '93 Jeep Wrangler 13.5 to 14.2?


What is the meter reading for a forward biased diode is likely to be when using the diode test range of a digital multimeter?

A: Nobody can answer that. It depends on the diode, battery on the meter, scale of the meter. It should never read zero or close to zero ohms and reversing the lead it should just be close to open but it may read some hi k ohms. A meter test is just to find shorted diodes and extremely leaking diode.


As you add more lamps to a parallel circuit what will the ammeter reading do?

If the amp meter is in series ahead of the first parallel branch of lamps the meter will read an increase in current.


How do you measure amps on a 208V single phase circuit with a clamp on amp meter?

Clamp the meter around the energized conductor that is connected to the load to be measured and read the amperage off of the dial face of the meter.


How can you tell that there is a current in a wire?

A clamp on amp meter is used for this purpose. When amperage is present in a wire there will be a magnetic field generated around the wire. The clamp on amp meter measures this magnetic field and converts it to an amperage value that is read on the screen of the amp meter. No current flow, no magnetic field, no reading. A dangerous and non recommended way to check current flow is to open the circuit when the load is connected and operating. There will be a small arc that jumps across the gap when the circuit is opened. This is current flowing in the circuit.


How does the current change in a circuit when the ammeter is placed in different spots?

the current value at any part of the circuit is dependent upon the circuit conditions and not the ammeter. The meter will simply allow you to read those currents, whatever they may be.