0
Just consider the a DC voltage as the function y = (DC value), lets call the DC value 1 volt. Then the integral of y=1 is y=x. The op amp will create a ramp that is representative of y=x until it saturates. Depending on the op amp, it will most likely saturate somewhere around Vcc - 2V. As soon as it hits this rail it will level off.
What else can I help you with?
How does the voltage applied to a circuit affect the current flowing through the wire?
Voltage is equal to the Current multiplied by the Resistance.Without changing the resistance, increasing the applied voltage in a circuit will increase current flow. There is a simple, direct relationship between voltage and current. Double the voltage, twice the current will flow. Triple the voltage, and the current will triple. As voltage (E) equals current (I) times resistance (R), when resistance is fixed, what happens to voltage will happen to current.
What will happen if current is more than required in diode?
If the applied voltage is greater than maximum forward voltage, the diode will get damaged..
What happen if you apply triangular input to transformer?
there will be no neutral point in the circuit and high voltage will be across the transformer coils
Why clipping happen for op-amp?
Clipping occurs in the voltage waveform when the input voltage, multiplied by the voltage gain of the op-amp circuit, exceeds the op-amp supply voltage as limited by the output network. The supply voltage and output network, limits the maximum voltage that can be achieved at the output. The op-amp behaves normally within its range of maximum voltage output, and then it is clipped when it reaches the maximum voltage of the circuit.
When an AC 5A and dc Current of 5A applied simultaneously to the circuit then what it happen?
A DC ammeter will read zero
What will happen to the transformer if the rated voltage is applied to the winding during short circuit test?
the winding would burn....
What will happen to the transformer if double the rated voltage is applied to the winding during the open circuit test?
no voltage will be induced on the secondary side of the motor as the windings will become saturated.
How does the voltage applied to a circuit affect the current flowing through the wire?
Voltage is equal to the Current multiplied by the Resistance.Without changing the resistance, increasing the applied voltage in a circuit will increase current flow. There is a simple, direct relationship between voltage and current. Double the voltage, twice the current will flow. Triple the voltage, and the current will triple. As voltage (E) equals current (I) times resistance (R), when resistance is fixed, what happens to voltage will happen to current.
What will happen to voltage in a parallel circuit?
In a parallel circuit the voltage across each component is the same.
What will happen in a circuit if the voltage does not change but the resistance in the circuit increases?
If the resistance increases, while the voltage stays the same, current will decrease. Current = voltage divided by resistance
When a low voltage current is applied to LCD screens what happen?
=== === === ===
What will happen if a piece of string is being used to complete a close circuit?
The piece of string will act as an insulator. Insulators will not carry circuit current when a voltage source is applied across it. Therefore nothing will happen if a piece of string is used to complete an electrical circuit.
What happen to the voltage when the collector current increases in a biased circuit?
it dies
If the resistance in the circuit is increased what will happen to the current and voltage?
* resistance increases voltage. Adding more resistance to a circuit will alter the circuit pathway(s) and that change will force a change in voltage, current or both. Adding resistance will affect circuit voltage and current differently depending on whether that resistance is added in series or parallel. (In the question asked, it was not specified.) For a series circuit with one or more resistors, adding resistance in series will reduce total current and will reduce the voltage drop across each existing resistor. (Less current through a resistor means less voltage drop across it.) Total voltage in the circuit will remain the same. (The rule being that the total applied voltage is said to be dropped or felt across the circuit as a whole.) And the sum of the voltage drops in a series circuit is equal to the applied voltage, of course. If resistance is added in parallel to a circuit with one existing circuit resistor, total current in the circuit will increase, and the voltage across the added resistor will be the same as it for the one existing resistor and will be equal to the applied voltage. (The rule being that if only one resistor is in a circuit, hooking another resistor in parallel will have no effect on the voltage drop across or current flow through that single original resistor.) Hooking another resistor across one resistor in a series circuit that has two or more existing resistors will result in an increase in total current in the circuit, an increase in the voltage drop across the other resistors in the circuit, and a decrease in the voltage drop across the resistor across which the newly added resistor has been connected. The newly added resistor will, of course, have the same voltage drop as the resistor across which it is connected.
When happen to the voltage when ressistor added to a circuit?
Just as the name of the component implies, electrical current gets resisted and therefore it diminishes unless an equally, larger voltage difference in that section of the circuit is applied. V=IR Current is inversely proportional to Resistance (when one goes UP, the other goes DOWN) Voltage is directly proportional to Resistance
What will happen to the generator voltage when the load fluctuates in distribution board?
The generator's voltage regulator will sense the fluctuation. If the voltage goes low more current will be applied to the armature to compensate. If the voltage goes high less current will be applied to the armature to compensate.
A lamp is connected to a battery if a capacitor is inserted in the positive wire between the battery and the lamp what will happen?
large capacitors will become charged in a fraction of a second if a DC voltage is applied to its terminalsonce a capacitor becomes fully charge it acts as an open circuit to direct current in other words, once the capacitor charged by a DC voltage, the current will cease to flow in the branch of the circuit which contains the capacitor.a capacitor also offers opposition known as (capacitive reactance) to alternating current. it does not , however ,act as an open circuit to when an a-c alternating current voltage is applied.
