The frequency must be the same and the phase must be the same as well. This can be indicated by having a lamp connected across the switch (for each phase if 3-phase).
When two generators are to be run in parallel, one generator is first started and some load is given. Then second generator is brought in parallel with the running generator (subject few conditions, like voltage, frequency, phase angle). First generator which is running is known as running generator, the second generator which gets connected is known as incoming generator
1.The effective voltages of the incoming generator must be exactly equal to that of the others or of the bus bars connecting them.2.The phase rotation or sequence of the running and incoming generators must be same.3. The frequency should be same.
the operation of connecting an alternator with other alternator or with common bus-bars is known as synchronizing.Generally alternator used in power system where they are connected in parallel with other alternator.condition for parallel operation of an alternator1. The terminal voltage of incoming alternator must be same as the bus-bars voltage.2. The speed of incoming alternator must be such that its frequency f =pn/120 as the same frequency of the bus-bars.3. The voltage of incoming alternator and the bus-bars voltage are in same phage.
A single tuned amplifier basically consists of a tuned circuit (which may consist of an IFT or a parallel tuned LC circuit) connected to the collector of an amplifier circuit (in Common Emitter configuration). The tuned circuit is designed to get a resonant frequency equal to the incoming frequency signal that arrives at the base. The Single Tuned Amplifier gives maximum amplification to that particular incoming frequency which matches the resonant frequency of the tuned circuit and attenuates all other frequencies. Thus it gives sharp selectivity with a high Q-factor.
In communications and electronic engineering, an intermediate frequency (IF) is a frequency to which a carrier frequency is shifted as an intermediate step in transmission or reception. [1] The intermediate frequency is created by mixing the carrier signal with a local oscillator signal in a process calledheterodyning, resulting in a signal at the difference or beat frequency. Intermediate frequencies are used in superheterodyne radio receivers, in which an incoming signal is shifted to an IF for amplification before final detection is done. The intermediate frequency stays the same for all signals, for example 455 kHz in an AM broadcast receiver.Conversion to an intermediate frequency is useful for several reasons. When several stages of filters are used, they can all be set to a fixed frequency, which makes them easier to build and to tune. Lower frequency transistors generally have higher gains so fewer stages are required. It's easier to make sharply selective filters at lower fixed frequencies.
When two generators are to be run in parallel, one generator is first started and some load is given. Then second generator is brought in parallel with the running generator (subject few conditions, like voltage, frequency, phase angle). First generator which is running is known as running generator, the second generator which gets connected is known as incoming generator
It is double of the incoming wave.
1.The effective voltages of the incoming generator must be exactly equal to that of the others or of the bus bars connecting them.2.The phase rotation or sequence of the running and incoming generators must be same.3. The frequency should be same.
the operation of connecting an alternator with other alternator or with common bus-bars is known as synchronizing.Generally alternator used in power system where they are connected in parallel with other alternator.condition for parallel operation of an alternator1. The terminal voltage of incoming alternator must be same as the bus-bars voltage.2. The speed of incoming alternator must be such that its frequency f =pn/120 as the same frequency of the bus-bars.3. The voltage of incoming alternator and the bus-bars voltage are in same phage.
interference between the incoming and reflected waves of the same frequency
The incoming frequency is fed to a transformer ( or IC chip). Another frequency is fed to that same place. The sums and differences are output. Differences are rectified to recover the modulated info.
Convert in coming signal to D.C. using a bridge rectifier. Use the voltage to run a voltage to frequency converter. You will have to scale the incoming signal to match the frequency range desired.
because the incoming generator has be connected as a source and not a load to the grid. if the frequency of the incoming generator is lower than the grid frequency then ... it will behave as a motor drawing power from the grid and generator will trip in reverse power protection.
In absorption, the frequency of the incoming light wave is at or near the energy levels of the electrons in the matter.
Six percent is immediately reflected by the atmosphere.(Source: NASA.See the related question below.)
A local oscillator is used in a superheterodyne radio circuit for example.The incoming radio frequency is mixed with an internal local oscillator circuit to generate a new intermediate frequency (IF) .The local oscillator usually runs at a frequency of 470kHz and is generated by an inductor and capacitor(LC oscillator)
A local oscillator is used in a superheterodyne radio circuit for example.The incoming radio frequency is mixed with an internal local oscillator circuit to generate a new intermediate frequency (IF) .The local oscillator usually runs at a frequency of 470kHz and is generated by an inductor and capacitor(LC oscillator)