answersLogoWhite

0

On a 240 volt outlet, such as a dryer outlet: G is Ground, W is Neutral, X and Y are the two Hot legs.

User Avatar

Wiki User

15y ago

What else can I help you with?

Continue Learning about Electrical Engineering

How do you upgrade household wiring from 110 volt to 220 volt?

your house has 220 you must use a 2 pole breaker. your wiring will change ,not a do it your selfer call someone


How much does it cost for an electrician to install a 220 plug for a stove?

The cost for an electrician to install a 220-volt plug for a stove typically ranges from $150 to $300, depending on factors such as location, labor rates, and any necessary modifications to the electrical system. Additional costs may arise if wiring upgrades or permits are required. It's advisable to get quotes from multiple electricians to ensure a fair price.


Can you add a 110 outlet from one leg of the 220 wiring?

Yes but I would not advise it. Get 110 volts somewhere else.


How can you supply 220v machine to 208v supply?

Most 220 volt equipment will work on 208 volt supply. If the machine has a resistive load then the watts output will be lower than if supplied from a 220 volt source. If it is a motor load you will find that the equipment may run a bit slower but most motors will take the lower voltage. If the machine is a plug in device, install the appropriate receptacle to match the pin configuration and plug it in. If it is a hard wire installation this should be done by a qualified person.


Can you collect one 220 volt phase from a 380 volt three phase plug?

Answer for UK and countries running a 50 Hz supply service.The voltage potential of 380 volts is not common to North America.It will probably be difficult to tap into the plug to get the voltage.If you have a three phase 380 volt supply from a source then you can obtain a single phase voltage of 220 volts from it. 220/380 is a wye voltage connection. 380 divided by 1.73 will give you 220 volts. L1 - N = 220V, L2 - N =220V, L3 - N = 220V. L1 - L2 = 380, L2 - L3=380, L3 - L1 = 380.

Related Questions

Somebody already asked this question above but got a half answer I need the other half. What plug socket does the UAE use?

220 volt electricity 3 prong plug.


What is the correct 220 plug wiring diagram for a specific appliance or device?

The correct 220 plug wiring diagram for a specific appliance or device can vary depending on the manufacturer and model. It is important to refer to the appliance's manual or contact the manufacturer for the precise wiring instructions to ensure safety and proper functioning.


How do you properly wire a 3 prong 220 plug?

To properly wire a 3-prong 220 plug, first, identify the hot wires (usually black and red) and the neutral wire (usually white). Connect the black and red wires to the two brass screws on the plug and the white wire to the silver screw. Make sure to tighten the screws securely and double-check your connections before plugging in the appliance.


What plug socket and voltage does South Africa have?

South Africa uses 220-240V/50H 3-prong plugs that look like this: http://www.jjeac.com/UploadFiles/JJA-14%20South%20Africa%20plug.jpg


What type of plug is required for a single phase 220 volt power supply?

A single phase 220 volt power supply typically requires a plug with three prongs, including two hot prongs and one ground prong. The specific type of plug needed may vary depending on the country or region.


What is wrong if you changed a four prong to a three prong and the dryer is not heating?

My question is WHY did you replace a four prong dryer plug with a three prong! 220 volt Electric dryers require two hot legs, a neutral and a system ground wire. Sounds as though you shunted one of the hots or the neutral. You need to install a four prong plug of the same configuration and wire it exactly as the original.


What is the configuration of 220 volt plug?

There are many different types of 220 Volt plug. Different plugs are used in different countries.Two pin plugs have two wires, live (brown) and neutral (blue).Three pin plugs have the two wires above, plus Earth (green/yellow).Rewireable plugs are labelled which wire goes where. The wiring colours are an international standard, unlike plugs.


How do you wire a 220 plug correctly?

To wire a 220 plug correctly, you need to connect the red and black wires to the hot terminals, the white wire to the neutral terminal, and the green or bare wire to the ground terminal. Make sure to follow the specific instructions provided with the plug and turn off the power before starting the wiring process.


What kind of electrical connection will you need in Paris?

two prong connector & 220 voltage converter


How do you correctly wire a three blade 220 volt plug?

To correctly wire a three-blade 220-volt plug, you should connect the hot wires (usually black and red) to the brass-colored screws, the neutral wire (usually white) to the silver-colored screw, and the ground wire (usually green or bare copper) to the green screw. Always make sure to follow the specific instructions provided by the plug's manufacturer and to disconnect power before working on any electrical connections.


Which is the positive terminal on a 3 prong 220 power cord?

A 220 volt power cord has 2 positive terminals. The will look the same. The one that is different will be the ground.


Where do you ground the extra wire when plugging a 4 prong wire into a three prong outlet for a dryer at?

If you are connecting a 4-prong dryer cord to a 3-prong outlet, the extra ground wire (green or bare copper wire) should be left unconnected. Do not try to ground it by connecting it to the neutral terminal or anywhere else. This is to prevent creating a ground loop and potentially causing a safety hazard.