answersLogoWhite

0

What else can I help you with?

Continue Learning about Electrical Engineering

Why do white wire mark 120v?

Because the white wire on a 120 volt circuit is the neutral wire that is connected to the silver screw on outlets and switches. It is connected to the neutral bar in the service panel.


What size wire for a 40 amp breaker?

A 40 amp breaker is used in conjunction with AWG # 8 copper wire. The black and red wires are connected to the breaker. The ground wire is connected to the ground bar and the white wire is connected to the neutral bar.


Why is it that when you touch the neutral in a box that is not connect to the panel cause the test light to come when touching the power wire?

It shouldn't. The open end of a non connected neutral should have the same potential as the voltage feeding the circuit. The only time a voltage will show is when the return neutral is tested with a meter to the neutral bar or the ground return bar. It will then show what the supply voltage to the connected load is. Once this neutral is connected to the neutral bar there will be no voltage shown across the test meter between the neutral and the neutral bar or the ground bar.


When wiring a kitchen stove must the ground wire be grounded?

Absolutely. You need the range ground to be fully connected back to the panel ground buss bar.


Can the ground wire from two separate circuits (one 20-amp one 15 amp) be shared?

There wasn't room for more details: I know they're shared on the bus bar. I meant to ask if they can be connected in the junction box? I found a jct box with the two circuits. They are completely separate except for the grounding conductor/ground wire, which are connected. This is because the 15-amp has armored BX and junctions with 14-2 romex, so the ground for the romex connects with the ground for the 12-2/20-amp. Thanks.

Related Questions

Why do white wire mark 120v?

Because the white wire on a 120 volt circuit is the neutral wire that is connected to the silver screw on outlets and switches. It is connected to the neutral bar in the service panel.


How do you know what wire is ground on 200 amp service?

On a 200 amp or any size service the ground wire is easily identified. Look in the distribution panel for the neutral bus bar. This is where the service neutral (white wire) is connected to the distribution panel. There you will see a bare copper wire connected to the same neutral bar. This is the ground wire that is connected to the ground rods out side of the house.


Can grounds and neutral wire share same buss bar?

No, the ground and neutral wires should not share the same bus bar in an electrical panel. The ground wire is for safety and should be connected to the ground bus bar, while the neutral wire is for returning current and should be connected to the neutral bus bar. Mixing them can cause dangerous conditions like electrical shock or fires.


What size wire for a 40 amp breaker?

A 40 amp breaker is used in conjunction with AWG # 8 copper wire. The black and red wires are connected to the breaker. The ground wire is connected to the ground bar and the white wire is connected to the neutral bar.


How do you wire a 15 amp breaker?

Ground wire connects to the ground bar, white wire connects to the neutral bar, and black wire connects to the breaker. Be sure and turn off main breaker before installing the wire or the breaker.


Should neutral wire of lamp be connected to the 3amp or the 6 amp side of a canopy switch?

You should never switch the neutral wire. The neutral of the appliance should be connected directly to the neutral wire leading to the service panel neutral bar.


Where should the ground wire be connected in the electrical circuit?

The ground wire should be connected to the grounding terminal or bus bar in the electrical circuit to provide a path for excess electrical current to safely flow to the earth.


Suppose you wrapped an iron bar with wire and connected the ends of the wire to a battery what is this device called what would happen to this device if you disconnected the battery?

This would be an Electromagnet...... If the battery is disconnected, then the iron bar will become a permanent magnet.


Can the ground and neutral wires be connected to the same bar in the main panel?

No, the ground and neutral wires should not be connected to the same bar in the main panel. It is important to keep them separate to ensure proper functioning of the electrical system and to prevent potential safety hazards.


What is the recommended 220 wiring diagram for installing a new electrical circuit in a residential home?

The recommended 220 wiring diagram for installing a new electrical circuit in a residential home typically involves using a double-pole circuit breaker and a 4-wire cable with two hot wires, a neutral wire, and a ground wire. The hot wires are connected to the circuit breaker, the neutral wire is connected to the neutral bus bar, and the ground wire is connected to the ground bus bar. It is important to follow all local electrical codes and regulations when installing a new electrical circuit.


In the typical home electrical panel installation the main ground wire is connected directly from a ground rod driven into the ground to the?

In North American residential homes, there are 3 wires coming from the utility company, two "hots" and neutral. The two "hot" conductors get connected to the main breaker. The neutral gets connected to the neutral bus bars located along the sides of the breaker box. There is a set screw that is placed in the neutral bar that screws into the distribution panel enclosure thereby bringing the potential of the neutral bars down to zero. The wire from your ground rod is also connected to the neutral bus bar, and thereby it is connected to the neutral from the power company. This is also often bonded to the copper cold water plumbing in the house if the home is not plumbed in PVC water pipe. White circuit wires are then connected to the neutral bus bars. Also in the distribution panel are ground bus bars. The ground wires from circuit cables are connected to these grounding bars. Do not under any circumstance terminate the white and bare ground wires together. Ground wires to the ground bar and white wires to the neutral bar.


How do you wire a wire to a wire?

If you are connecting 120 volts, you connect the black wire to the breaker, white wire to the neutral bar, and ground wire to the ground bar. If you are connecting 240 volts connect the black & white wires to the breaker, & ground wire to the ground bar.