off center
an electric desalter is one which uses a high electric potential to separate the salts present in the crude. it is a horizontal drum .it forms an emulsion with crude an emulsion is a mixture of crude and water.water added to the crude acts as an solvent for dissolving the salts present in the crude .once these salts are properly dissolved the electric charge breaks these salts into charged ions and form a dipole .water along with salts settle at the bottom and the crude overflows to the fractionation column
You can request a wiring diagram from Hyster Company. Just visit their website at http://hyster.com/americas/en-US and click on Contact Us at the bottom of the page.
The rate at which an appliance takes energy from the electrical outlet and spinsthe electric meter is the "power" shown on the data label, usually on the backor the bottom of the appliance.The rate at which it actually converts the energy into the form required to do itsjob is also a "power" figure. This one is always less than the power taken fromthe wall outlet, and is not always stated or marked on the appliance.A couple of cases where it is clearly stated:-- Microwave Oven: " 600 Watts of Cooking Power "The microwave oven is using perhaps 1,500 to 2,000 watts from the electric company,converting some of it into radio waves (with less than 100% efficiency), and delivering600 watts of microwave radiation to the cooking chamber.-- Blow Drier: " 1,250 Watts of Drying Power "The blow drier is using perhaps 1,500 watts from the electric company, anddelivering useful energy at the rate of 1,250 watts, in form of a hot coil anda strong little fan motor to blow air across the coil.But on an electric stove, furnace, blender, food processor, fan, telephone, TV,computer, vacuum, washer, dryer, etc., you can find the power consumptionmarked somewhere on it, but it's not clear exactly where that power goes.
The standard height is around 12" to 15" the bottom of the box above the floor but for the disabled you can install them higher but no more than 48" above the floor. Pick a height that will work for the disabled and install all of them the exact same height.
You need to have a grounding rod made of galvanized steel that is driven straight into the ground until only half an inch of bar is remaining above ground. The ground rod should be at least 6 feet in length. Drier land areas normally require a longer grounding rod, or more of them, spaced 10 feet apart. The ground rods themselves should be placed in [an] area[s] that are naturally permanently moist to have any effect. Then you have to run a grounding cable that is attached to the ground rod along the bottom or top of the fence (can be the top wire or bottom wire) all the way to the fence charger. This cable needs to be attached to the ground rod by ground rod clamps That grounding cable should be attached to that fence charger in order for the fence to be properly grounded. Check out the following links on tips and instructions on how to properly ground an electric fence.
Iron is removed from a blast furnace through a process called tapping, where a hole at the base of the furnace is opened to release the molten iron. The iron is then cast into molds to solidify and form pig iron or further processed into steel.
It is so that the inside bottom of the line can drain completely if required and no fluid or condensate will remain trapped. In other words the eccentric reducer keeps the bottom of the line straight.
the blast furnace got its name , because its bottom which is called a furnace blows hot air to go up.
A furnace or fireplace or the ash dump box.
iron is collected from blast furnace by drilling the taphole.Taphole is a hole drill and plug after cycle of time located in blast furnace bottom.
The blast furnace maintains heat through the combustion of coke (a type of coal) with hot air blown in at the bottom. This creates a high temperature that allows the iron ore to melt and collect at the bottom of the furnace. The heat is further sustained by the chemical reactions occurring within the furnace.
they like you or want to annoy you
Doesn't matter
Gather materials: Obtain ore, fuel, and a furnace. Preheat the furnace: Start the furnace and allow it to reach the necessary temperature. Add materials: Place the ore and fuel into the furnace. Extract metal: As the ore melts, the metal will separate and collect at the bottom of the furnace.
keep tapping on the bottom screen with your pen
It is called an upflow furnace. This type of furnace takes in air at the bottom, heats it, and then releases it through the top vents.
The pilot light in your furnace is typically located near the bottom of the furnace, usually behind a small access panel. It is a small flame that ignites the gas to start the heating process.