0
for stability
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
Why does the emitter bypass capacitor increase the voltage gain?
In the common emitter configuration, gain is hFe or collector resistance divided by emitter resistance, whichever is less. Placing a capacitor across the emitter resistor effectively makes the emitter resistor less, for higher frequencies, so the gain is higher for higher frequencies. This creates a high pass filter, or a low cut filter, depending on what you want to call it.
What is use of capacitor Ce across emitter resistance?
It can be used as a feedback and to ground unwanted signals and frequencies
Why output of common emitter amplifier is inverted?
In a common emitter amplifier, the base-emitter current causes a corresponding collector-emitter current, in the ratio of hFe (beta gain) or collector resistance over emitter resistance, which ever is less. Since this ratio is usually greater than one, the differential collector current is greater than the differential base current. This results in amplification of the base signal. As you increase the base-emitter current, the collector-emitter current also increases. This results in the collector being pulled towards the emitter, with the result that the differential collector voltage decreases. This results in inversion of the base signal.
What is the Effect of collector resistance in emitter follower circuit?
Colector resistance in an emitter follower circuit serves to place a limit on how much current can be supplied by the transistor. Often, the resistor is sized so that a short circuit in the load does not cause the transistor to fail.
Why emitter follower is called so?
Because of the geometry of the common collector configuration, changes in base voltage appear at the emitter. Said another way, what happens at the base pretty much happens at the emitter, and the emitter can be said to "mirror" or "follow" the base. The emitter is a follower of the base, and the name emitter follower appeared and was used.
What is the Frequency response of common emitter amplifier?
The voltage gain is a measure of the amplified output available at the collector terminal divided by the voltage measured on the base. This if you have 10 mV applied to the base and voltage of 1 volt at the collector the voltage gain is 100ANSWERThe maximum voltage gain of a common emitter amplifier is dependant on the transistor itself. Some have only a very small voltage gain such as in Radio Frequency Power transistors. These are almost all used as common emitter circuits for bipolar transistors or common source for FETs.. On the other hand some darlington transistors can have common emitter gains of hundreds of thousands. If the stage has an unbypassed emitter resistor, the voltage gain is equal to Rload/RE, (Rload is the parallel value of the resistance from collector to the supply and the resistance of the load).If the emitter resistance is bypassed, the value of resistance to be used for RE is the internal Re which is equal to 25mV/Ie
Why a capacitor is used for amplification in common emitter circuit?
A: The ratio of emitter/collector resistance is the gain. by adding a capacitor on the emitter the AC parameters will shift as a function of frequency
Why would there be a gain when you add the emitter capacitor to a circuit board?
A capacitor has lower resistance (impedance) as frequency increases. Adding an emitter capacitor effectively lowers the emitter resistance as frequency increases. Since gain in a typical common emitter amplifier is collector resitance divided by emitter resistance, this decrease in emitter resistance will increase gain as frequency increases.
Why bypass capacitor is used in common emitter ampifier circuit?
If a bypass capacitor is used the voltage drop across emitter resistance is reduced which in turn increases the gain.....
What is the effect of emitter resistance in common emitter amplifier?
The gain of a common-emitter amplifier is collector resistor divided by emitter resistor, or hFe, whichever is less. Since hFe depends on temperature, designing the amplifier to be dependent on resistance ratio makes it more stable. As such, the emitter resistance serves to stabilize the amplifier.
What is swamping resistance?
(Electronics) Resistor placed in the emitter lead of a transistor circuit to minimize the effects of temperature on the emitter-base junction resistance and its resistance is called swamping resistance.
What is the function of emitter bypass capacitor in common emitter amplifier?
The emitter bypass capacitor in a common emitter amplifier will have less resistance as the frequency increases. Since gain in this configuration is collector resistance divided by emitter resistance (within limits of hFe), the gain will thus increase for higher frequencies, making this into a high pass filter.
Why does the emitter bypass capacitor increase the voltage gain?
In the common emitter configuration, gain is hFe or collector resistance divided by emitter resistance, whichever is less. Placing a capacitor across the emitter resistor effectively makes the emitter resistor less, for higher frequencies, so the gain is higher for higher frequencies. This creates a high pass filter, or a low cut filter, depending on what you want to call it.
What will happen to voltage divider circuit if emitter resistance is greater than collector resistance?
The gain of a class A, common emitter BJT amplifier, a fairly standard configuration, is defined as collector resistance divided by emitter resistance, or as hFe, whichever is less. Assuming that we are operating in a linear mode, and hFe is not a limiting factor, then the emitter resistance being greater than the collector resistance simply means that the gain is less than one.
What is the effect of no emitter resistance on common emitter amplifier?
Limit current through emitter, Often the resistance is the load itself. So the restatnce limits current on what otherwise would act as a voltage follower.
What is use of capacitor Ce across emitter resistance?
It can be used as a feedback and to ground unwanted signals and frequencies
True or false a high resistance between the collector and emitter when a transistor is switched off?
yes , it has high resistance between collector and emitter on the off state.
