answersLogoWhite

0

a fuse wire melts when current passing through it exceeds a certain value as in overloading and short circuiting .this breaks the circuit prventing further current flow and damage ..

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Electrical Engineering

How do you change wire fuse for circuit breaker?

A circuit breaker does not have a wire fuse in it.


What is the best suitable component for circuit protection instead of fuse?

circuit breaker, or "resettable fuse", which is a reallya small circuit breaker in the housing of a fuse


Why would a 63 amp fuse holder get hot?

The only time that fuse holders gets hot is when there is a loose connection between the fuse holder and the wire connected to the holder. If this is happening remove the supply voltage from the circuit that the fuse holder is in. Remove the wire from the holder. Cut the burned end of if there is enough wire and re install. If not enough wire, use a wire brush to get the oxidation off of the wire. Apply a coating of anti oxidation compound on the wire end and then re install into the holder. Tighten the wire into the holder very tightly. Check the spring clamping pressure of the fuse end of where the heating occurred. This spring clamping pressure is important for low resistance conductivity. If the fuse feels loose when installed change the fuse holder for a new one.


Can you replace a 15 amp fuse with a 30 amp fuse?

Sure, you can replace a 15 amp fuse with a 30 amp fuse, but it's not recommended. The 30 amp fuse has a higher current rating, which means it can allow more current to flow through the circuit than what it was designed for. This can pose a fire hazard and damage your electrical equipment. So, technically you can do it, but it's like putting a square peg in a round hole - it might fit, but it's not a good idea.


How do you wire a 240 volt street light circuit?

A 240 volt street light circuit is wired in parallel connections. In the base of the street fixture an inline fuse is connected into the circuit that goes up to the fixture to protect the lamp head.

Related Questions

Why the fuse wire necessary in a circuit?

It is a safety device. It is not an essential part of the circuit.


How do you change wire fuse for circuit breaker?

A circuit breaker does not have a wire fuse in it.


What wire in a circuit should contain the fuse?

The wire that connects the power source to the rest of the circuit should contain the fuse. This is typically the wire that leads directly from the positive terminal of the battery or power source. Placing the fuse in this wire helps protect the circuit in case of a short circuit or overload.


What is fuse what is it made up of?

A fuse in its simplest form - is simply a short piece of wire that is weaker than the circuit it is protecting. When the current flowing through the circuit exceeds the fuse rating, the fuse wire melts - breaking the circuit.


What will happen if a thick copper wire is used in fuse?

If a thick copper wire is used in a fuse then by definition of a fuse this device would no longer be defined as a fuse. A fuse in a circuit is used to protect the conductors feeding the load of that circuit. The circuit, if using a thick copper wire in a fuse, would then be considered as a non fused circuit.


What is the advantage of electric fuse in an electric circuit?

A fuse is intended to be a weak link of thin wire that goes in series with a circuit. If the current becomes too high for any reason, the fuse wire melts and cuts off the supply. Without a fuse, the circuit will heat up until something else melts, which might cause a fire. So fuses are necessary to prevent electrical fires.


Why does the wire from the fuse box to the head light switch burn up?

Check the headlight fuse that's INSIDE the box. If an oversized fuse has been put in the fusebox you will have problems with the wire overheating whenever there is a problem in the circuit. There is a short circuit (wire touching chassis ground) somewhere in the lighting circuit, but the wire is burning because an oversized fuse has been put in the circuit.


Do you connect a fuse to the live wire or the neutral wire?

A fuse is typically connected to the live wire in a circuit. This is done to protect the circuit from an overload or short circuit, as the fuse will blow or trip and cut off the current flow if there is an issue.


What wire is the fuse always placed in?

The fuse is always placed in the hot wire (usually black in color) in a circuit. This is to protect the circuit from excessive current flow, which could lead to overheating and potentially cause a fire. Placing the fuse in the hot wire allows it to interrupt the circuit in case of a fault.


How does a fuse prevent an overlode circuit?

A fuse contains a wire that will melt and break the circuit if too much current flows through it, preventing an overload. When the current exceeds the fuse's rating, the wire melts, interrupting the flow of electricity and protecting the circuit from damage.


What happen if fuse is connected to neutral wire?

The fuse will be blown off in case of any fault. But the circuit will not be isolated because of the presence of fuse in nutral line. current will still flow and the line will be so dangerous.


What happen when a fuse wire of 100 ampere is used when a circuit at home draws a maximum current of 20 ampere?

The fuse or breaker should be no bigger than specified for the wiring and devices on the circuit. Your nominal current draw may be 20 amps, but a short circuit would cause maximum current to flow which in this case would be 100 amps until the fuse blew.