It does not matter what line in (the phase or neutral) is the fuse. In a closed series circuit current in all areas of the circuit is equal. It's best to put the fuses in both wires (phase and neutral) and even better for each individual device in the chain.
To protect a circuit, we use a fuse or circuit breaker. The fuse or circuit breaker must always be placed in the lineconductor, never in the neutral conductor. So, if we want to completely isolate a circuit from the supply, we must remove the fuse from the line conductor, and open the link in the neutral conductor. A 'link' is a non-fusible metal break point in the neutral.
A fuse should always be inserted into the line conductor, never the neutral conductor. If a fuse has been inserted, inadvertently, into the neutral, an overload will still operate the fuse, but the line voltage will not be isolated from the circuit -thus presenting a shock hazard. Furthermore, it will not protect against an earth (ground) fault that occurs in the circuit.
In a MEN (Multiple Earth Neutral) system, the neutral wire is connected to the earth wire at the switchboard. This is the neutral link. From an electrical point of view the neutral pin and the earth pin in a power socket are at the same potential but from a safety point of view they are different. A residual current device (RCD) (or earth leakage core-balance-relay(ELCBR)) sits in series with both the active and the neutral feed and a leakage from either wire to ground (via a human or water leak in a washing machine etc) will trip the circuit breaker that is in the RCD.Another AnswerFuses or circuit breakers must be inserted into the line conductor, never into the neutral conductor. However, if we need to isolate the circuit, we must place a break in both the line and the neutral conductors. We can achieve this for the line conductor by, for example, removing the fuse. To achieve the same with the neutral conductor, we can open the neutral link, which is simply a short length of conductor inserted between a pair of terminals in the neutral.
Protect the circuit with an OCPD, an over current protection device, such as a circuit breaker or fuse.
A circuit breaker is designed to 'break' in a circuit if a short circuit (or other malfunction) occurs. This prevents overheating (or burn-out) of the circuit wires. In older systems, you would need to find which fuse wire has fused and replace it. In a circuit breaker, once the fault has been found and corrected, the breaker is simply switched back on.
To protect a circuit, we use a fuse or circuit breaker. The fuse or circuit breaker must always be placed in the lineconductor, never in the neutral conductor. So, if we want to completely isolate a circuit from the supply, we must remove the fuse from the line conductor, and open the link in the neutral conductor. A 'link' is a non-fusible metal break point in the neutral.
The neutral line in home electricity completes the circuit by providing a return path for current to flow back to the electrical source. It helps balance the electrical load and provides a reference point for voltage measurements. Without a neutral line, the circuit would not function properly and could pose safety risks.
A popped fuse in an electrical circuit could be caused by an overload of electrical current or a short circuit.
fuse
The fuse will be blown off in case of any fault. But the circuit will not be isolated because of the presence of fuse in nutral line. current will still flow and the line will be so dangerous.
The neutral wire in a fuse box is typically colored white or gray to indicate that it carries the return current from the electrical circuit back to the service panel. It is important to consult local electrical codes and standards, as wire colors can vary by region.
Suppose there is a fuse which is connected to a live wire and it breaks some day because of excessive power supply. The light goes off because of that. You think that there is no power supply, but actually the neutral wire is taking current towards you. You carelessly try to repair the fuse, and you get a shock. Thus, neutral wires are not preferred in fuse.
An alternative to using a fuse is to use an electrical circuit breaker.
No, a fuse is a safety device designed to protect an electrical circuit from excessive current by breaking the circuit when the current exceeds a certain level. It is not meant to store electrical charge.
A fuse or circuit breaker will fit this description.
An alternative to using a fuse is to use an electrical circuit breaker.
A fuse is not used for increasing electrical current. Fuses are designed to protect electrical circuits by breaking the circuit when there is an overload or short circuit, preventing damage to the circuit and potential fire hazards.