0
Yes, but the transformer must have both the hot and neutral to work as designed. A auto-transformer is not a variable resistor that could reduce current/voltage by a change in the resistance which could be used in the hot and or neutral wire. An auto-transformer is designed to have the hot wire and neutral on each end of the winding with a variable tap in between. The resistance of the transformer and the inductance will effect the circuit to a limited way if placed in the neutral but this effect will not vary the voltage over the full range, the amount of voltage reduction will vary with the load's current draw, see ohms law. Neither a resistor or a auto-transformer connected in the neutral line only will increase the voltage above the level of the input like a correctly connected auto-transformer . Stanley
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Vector group of autotransformer?
YNyn0
What function does a capacitor serve in an auto transformer?
An autotransformer does not normally use any capacitors as it is a transformer with one winding and the lower voltage is taken from a tap part-way up the winding. A capacitor could be added if there is a concern about the power factor presented by the autotransformer to the supply.
What is single phase autotransformer?
An autotransformer is a transformer with at least two windings where a part of one winding (the common winding) is shared between both primary and secondary outputs.
How many windings does a auto-transformer have?
A true autotransformer consists of one, tapped, winding. For a step-down transformer, part of the winding is in series with the supply and the other part is common to both the supply and the load. For a step-up autotransformer, part of the winding is in series with the load, while the other part is common to both supply and load.But you can also use a mutual transformer as an autotransformer, by connecting the two windings in series and, then, described as above.
What does auto in autotransformer stands for?
"Auto" refers to the single winding used an auto transformer.
How do you install a 110v receptacle from a 3 phase breaker box if there are no neutrals in the breaker box?
If there is no neutral available you cannot, unless you use an autotransformer and derive a neutral. A panel with no neutral is called a power panel and is used to supply 240 single and three phase loads.
Why you not use auto transformer for distribution purpose?
because autotransformer used for both purpose step up and step down but dustrubution need step down in case of this autotransformer not used for dustrubtion purpouseAnswerBecause an autotransformer (not 'auto transformer') does not provide electrical isolation between the secondary and primary.
Advantages of autotransformer?
the power can flow either way through autotransformer (345/120 kV) ?
What is an autotransformer?
An autotransformer is a transformer where the primary and secondary are a single winding.
How many coils does a autotransformer have?
only single coil is use as a primary and secondary coil in a auto transformer.
Vector group of autotransformer?
YNyn0
Who invented autotransformer?
Talha Idrees
What does cwa stand for?
Constant Wattage Autotransformer
What function does a capacitor serve in an auto transformer?
An autotransformer does not normally use any capacitors as it is a transformer with one winding and the lower voltage is taken from a tap part-way up the winding. A capacitor could be added if there is a concern about the power factor presented by the autotransformer to the supply.
What is the another name of autotransformer?
autostep down transformer
What is single phase autotransformer?
An autotransformer is a transformer with at least two windings where a part of one winding (the common winding) is shared between both primary and secondary outputs.
How many windings does a auto-transformer have?
A true autotransformer consists of one, tapped, winding. For a step-down transformer, part of the winding is in series with the supply and the other part is common to both the supply and the load. For a step-up autotransformer, part of the winding is in series with the load, while the other part is common to both supply and load.But you can also use a mutual transformer as an autotransformer, by connecting the two windings in series and, then, described as above.
