0
A typical resistor will burn out when it dissipates power in excess of double its power dissipation rating for an extended period of time.
The power dissipated by a resistor is equal to I2R or E2/R, where
E = the voltage across the resistor
I = the current through the resistor
R = the resistance of the resistor
What else can I help you with?
Are resistors normally short when they burn out?
When resistors burn out, they typically fail in an open circuit condition rather than a short circuit. This means that they stop conducting electricity altogether, which can cause the circuit to break. However, in some cases, particularly with low-quality resistors, they may fail short, allowing current to flow freely. Overall, open failures are more common than short failures in resistors.
How do you reduce a line level audio signal to a mic level In a low impedance circuit?
To reduce a line level audio signal to mic level in a low impedance circuit, you can use a passive attenuator, such as a voltage divider, consisting of resistors. This involves selecting two resistors: one connected to the line level source and the other connected to ground. The output is taken from the junction of the two resistors, which effectively lowers the signal voltage to mic level. Alternatively, an active solution like a preamp can be used to match impedance and adjust the signal level more effectively.
What happens to the value of a resistor when it goes bad?
we can say that a resistor gone bad if 1. its resistance is different than that printed by the color code 2. doesn't conduct any current Resistors normally will burn open. Carbon resistors almost always do this, while wireound resistors can lower in resistance. They may still allow current flow, but it will not be correct.
What is the advantage of film resistors over carbon resister?
Film resistors have lower noise than carbon resistors.
When resistors are connected in series then what happens to the watt?
Resistors are rated in wattage so the lowest wattage rating will be the wattage of the series circuit. It will be able to handle that power any more and the lowest wattage resistor could be damaged and fail.Another AnswerWhen two or more resistors are connected in series, the resistor with the lowest resistance will operate at the highest power. If the power developed by a resistor exceeds its rated power, then the resistor may burn out.
What is resistence tolerence?
The typical spread (deviation) from the nominal value of the resistance of several resistors.
Are resistors normally short when they burn out?
When resistors burn out, they typically fail in an open circuit condition rather than a short circuit. This means that they stop conducting electricity altogether, which can cause the circuit to break. However, in some cases, particularly with low-quality resistors, they may fail short, allowing current to flow freely. Overall, open failures are more common than short failures in resistors.
How hot does a typical house fire burn?
A typical house fire can burn at temperatures ranging from 1,100 to 1,600 degrees Fahrenheit.
How can you fix a heater and AC fan that only work on high?
Resistors control the speed of the AC/Heater fan. These resistors are switched on and off in various combinations to create the different fan speeds. When the resistors burn out your fan will only work on the "HI" setting. The "HI" setting doesn't use any of the resistors and that's why it works. These resistors are near the blower and the blower is beneath the dashboard on the pasenger side. Just have to located resistors now.
What seems to be typical educational level?
The typical education level is low.
What seems to be the typical educational level?
The typical education level is low.
Why would the heating-AC fan on a 1994 Dodge Caravan only run on high?
Resistors control the speed of the AC/Heater fan. These resistors are switched on and off in various combinations to create the different fan speeds. When the resistors burn out your fan will only work on the "HI" setting. The "HI" setting doesn't use any of the resistors and that's why it works. These resistors are near the blower and the blower is beneath the dashboard on the pasenger side
How do you reduce a line level audio signal to a mic level In a low impedance circuit?
To reduce a line level audio signal to mic level in a low impedance circuit, you can use a passive attenuator, such as a voltage divider, consisting of resistors. This involves selecting two resistors: one connected to the line level source and the other connected to ground. The output is taken from the junction of the two resistors, which effectively lowers the signal voltage to mic level. Alternatively, an active solution like a preamp can be used to match impedance and adjust the signal level more effectively.
How do you repair an air conditioner on a 1996 Nissan Sentra that only works on level 4 and nothing happens on levels 1 2 and 3?
A resistor block controls the speed of the AC/Heater fan. These resistors are switched on and off in various combinations to create the different fan speeds. When the resistors burn out, your fan will only work on the "HI" setting. The "HI" setting doesn't use any of the resistors and that's why it works. These resistors are near the blower and the blower is beneath the dashboard on the pasenger side. A/C is probably fine. If you try the heater, it will show the same problem as your question.
Why do you need 330 ohm resistor for LED?
Generally 330ohm resistors are used to power a typical 3 volt LED if the source voltage is 5v
Is level 5 good for a yr 6?
Yes, level 5 is good for a year 6. Here is a simple table to show you the expectations of a child: Level W Working towards level 1, very weak Level 1 Average for a typical 5 year old Level 2 Average for a typical 7 year old Level 3 Average for a typical 9 year old Level 4 Average for a typical 11 year old Level 5 Average for a typical 13 year old Level 6 Average for a typical 14 year old Level 7 Above average for typical 14 yr old Level 8 Only available in maths Hope this helps :) http://www.satsguide.co.uk/what_are_sats.htm
What happens to the value of a resistor when it goes bad?
we can say that a resistor gone bad if 1. its resistance is different than that printed by the color code 2. doesn't conduct any current Resistors normally will burn open. Carbon resistors almost always do this, while wireound resistors can lower in resistance. They may still allow current flow, but it will not be correct.
