0
Obviously it would depend on the stainless grade because stainless is an alloy, so the speed rate would differ slightly depending on your grade.
The most important factor would be the type of cutter you use, if you are using Carbide cutting tools, with sufficient coolant you can run it at about 90-110 m/p/m (90 to 100 meters per minute)
If you using high speed steel cutters run it no more than about 30m/p/m.
My best advice to you is to ask for the manufactures recommendations they will give you a limit to work in, always start between lowest and middle of manufactures speed recomendations and then work your way up in speed if necessary. If your speed is correct you get a better finish and longer toolife.
Remember that if you run tools at higher speeds you decrease their life, the time taken to cut the material is determined by the feed-rate and not the speed, even on a lathe which has feed set to federate per revolution will only differ slightly.
Hope this helps…
What else can I help you with?
What is profiling on lathe machine?
Vertical milling machine is for cutting large pieces. The lathe cutting tool motion is perpendicular to the ground. They are said to Karosl lathe.
What is carriage in lathe machine?
carriage is a part of lathe which means to be support cutting tool to give feed to cutting tool and control cutting action.
Who puts a block of steel in a lathe and by grinding cutting to make a machine part?
A turner, machinist or lathe operator.
Where was the discovery of lathe machine?
Jacques de Vaucanson built the first all-metal lathe around 1751, according to Book Rags. Henry Maudslay, who is considered the "father of the industrial lathe," invented the first screw-cutting engine lathe in 1797.
Difference between single-point cutting tool use in lathe and shaping machine?
explain the difference between single point & multi point cutting tool
What is profiling on lathe machine?
Vertical milling machine is for cutting large pieces. The lathe cutting tool motion is perpendicular to the ground. They are said to Karosl lathe.
What is carriage in lathe machine?
carriage is a part of lathe which means to be support cutting tool to give feed to cutting tool and control cutting action.
Cutting parameters of lathe machine?
care gay boy
Who puts a block of steel in a lathe and by grinding cutting to make a machine part?
A turner, machinist or lathe operator.
What is function Spindles in the lathe?
function spindles in the lathe There is a long time to find a center cutting machine parts and maintenance.
What is tpi in lathe machine?
refers to the threads per inch for example screw cutting
Your lathe is not cutting correct screw pitch?
1 - You can control the angle of the screw cutting tools. 2 - setting screw cutting lathe control. 3 - reduce the depth at every step. 4 - Adjust the speed milling machine. 5 - Barry screws to release the lever, do not screw cutting lathe.
What is feed in lathe in machine?
non- examples of feed in lathe machine?
Where was the discovery of lathe machine?
Jacques de Vaucanson built the first all-metal lathe around 1751, according to Book Rags. Henry Maudslay, who is considered the "father of the industrial lathe," invented the first screw-cutting engine lathe in 1797.
What are the key differences between a wood lathe and a metal lathe, and how can one effectively utilize both wood and metal on a lathe machine?
A wood lathe is designed for shaping wood, while a metal lathe is used for shaping metal. The key differences lie in the materials they are meant to work with and the cutting tools used. To effectively utilize both wood and metal on a lathe machine, it is important to adjust the speed, cutting tools, and techniques based on the material being worked on. Additionally, using appropriate safety measures and understanding the properties of each material is crucial for successful lathe work.
Difference between single-point cutting tool use in lathe and shaping machine?
explain the difference between single point & multi point cutting tool
What is difference between turning machine and lathe machine?
There is no difference between a turning machine and a lathe. They are two names for the same kind of machine
