It is not possible to blast a hole in 2 inch steel plate with a 12 gauge slug. The slug will barely dent the plate, if it does anything at all.
GAUGE , is one inch thick of steel or metal. So, take this one inch thick of steel sheet and cut it into 12 equal thickness sheets , you get a 12 gauge steel sheet. Similarly, take this one inch thick of steel sheet and cut it into 14 equal thickness sheets , you get a 14 gauge steel sheet. and so on . So, a 12 gauge steel sheet is thicker than 14 gauge , 14 is thicker than 16 , 16 is thicker than 18 and so on. Wrong!!! See my discussion on this...
3/16" or 0.1875" *** 7 gauge steel sheet is .1793", not .1875" *** Different metals have different thickness for their gauge...mild steel is .1793, aluminum is .1443, stainless steel is .1875
The weight of a 6-inch, 18-foot heavy gauge steel stud can vary based on the specific gauge of the steel, but typically, heavy gauge steel studs weigh approximately 1.5 to 2.0 pounds per linear foot. Therefore, an 18-foot stud would weigh between 27 to 36 pounds. For precise weight, it’s best to refer to the manufacturer's specifications for the specific gauge being used.
Unprotected steel is generally not recognized as having a fire resistance rating.
The strength, durability, and longevity of steel caskets depends first of all on the quality and thickness of the metal sheets used. The United States Standard Gauge for the thickness of metal sheets is based on the number of sheets required to total one inch. The gauge number (ga) informs about the thickness of the steel sheets in such a way that the lower the gauge number, the thicker the steel. Low cost carbon steel caskets are usually made of 20-gauge steel. (20 sheets of 20ga steel have a thickness of one inch.) Twenty gauge steel sheets have a thickness of 1/20" or 0,8 mm; this is the same thickness as used in many automobile body panels. More expensive steel Caskets are made from 18- and 16-gauge steel. 16 ga steel sheets have a thickness of 1/16" or 1,3 mm. 16 ga steel is twice as heavy as 20 ga steel, 140% stronger and has a 140% longer life than 20ga.
A 21 Gage Steel plate is about 1/32 inch thick. Various charts put it at .032" to .033". That is for plain steel. Galvanized, aluminum and stainless have different measurements for the same gage.
17/64ths of an inch for steel
Between 6 and 7 gauge. 6 is thicker at .194 inch. 7 is thinner at .179 inch.
GAUGE , is one inch thick of steel or metal. So, take this one inch thick of steel sheet and cut it into 12 equal thickness sheets , you get a 12 gauge steel sheet. Similarly, take this one inch thick of steel sheet and cut it into 14 equal thickness sheets , you get a 14 gauge steel sheet. and so on . So, a 12 gauge steel sheet is thicker than 14 gauge , 14 is thicker than 16 , 16 is thicker than 18 and so on. Wrong!!! See my discussion on this...
3/16" or 0.1875" *** 7 gauge steel sheet is .1793", not .1875" *** Different metals have different thickness for their gauge...mild steel is .1793, aluminum is .1443, stainless steel is .1875
A steel plate of that size would weigh approximately 368 pounds.
26 gauge wire typically has a diameter of about 0.405 mm (0.016 inches). This gauge is considered relatively thin and is commonly used for jewelry making, crafting, and finer electrical wiring applications.
It is thicker than 1/8th inch thick steel.
.0500 inches or 1.27 mm
with your face
A quarter-inch steel plate can typically handle around 400-500 pounds of lateral pressure per square inch before yielding or deforming. However, the exact capacity can vary based on the grade of steel, the specific plate dimensions, and the nature of the load application. It is recommended to consult with a structural engineer for a precise analysis.
The volume of the plate is (0.5 x 20 x 45) = 450 cubic inchesThe weight is (450) x (0.28) = 126 pounds