answersLogoWhite

0

What else can I help you with?

Continue Learning about Engineering

Can you drain a leaking hot water heater by running hot water in home?

No, you have to attach a garden hose to the fitting at the bottom of the tank. Often the tank will have sediment built up in it and the water will drain very slowly from this.


How do you stop the drain valve of a hot water heater from dripping. Is it safe to put a cap on it?

No dont even think about putting a cap on it, its dripping for a reason, call a plumber to fix it, a hot water heater is a dangerous appliance and should not be dealt with lightly. If you have a drip, but can't fix it or get a plumber out right away, use a garden hose to route the water to a drain nearby. Most drain valves are threaded with garden hose fittings.


Who invented the pocket hose?

The patented pocket hose, called the Dap Hose was invented by the Dap Company.


Why does the water from the disposal side of the double sink drain into the dishwasher?

Probably the drain hose from the dishwasher isn't high enough to keep the water from running back . The hose should be above the level of the disposal at some point. Some states require an "air gap" which is a device that is placed in the drain line to prevent this. Some states require a simple high loop in the drain hose. Many dishwasher manufacturers are now installing backflow preventers in the dishwasher.


Do you need to replace hot water heater if the bottom of the heater is rusted?

If not leaking and water heater is working fine, no.Improved answer. -Drain and clean out your tank, and change the anode.Drain a H/W tankYou first turn OFF the power to tank, then attach a hose pipe to the bottom fitting, lead it outside or to any drain, turn on the valve by it, turn OFF your inlet valve and open the relief valve so air can enter the H/W tank.Let the whole tank empty -takes about 30 -40 minutes. Next, when empty turn ON the inlet valve and let cold water run through the tank and out the hose, now you will see the sludge coming out. Let this run 5-7 minutes or until water is coming through clean. Now you are done . Let it fill, then turn on power.

Related Questions

How can I effectively drain a water heater without a floor drain?

To effectively drain a water heater without a floor drain, you can use a garden hose to siphon the water out. Attach the hose to the drain valve at the bottom of the water heater and run the other end of the hose to a lower area where the water can safely drain. Open the drain valve and let the water flow out through the hose. Make sure to turn off the water heater and let it cool down before draining to avoid burns.


How can I effectively drain a Rheem water heater?

To effectively drain a Rheem water heater, follow these steps: Turn off the power or gas supply to the water heater. Connect a garden hose to the drain valve at the bottom of the heater. Place the other end of the hose in a drain or outside. Open the drain valve and let the water heater drain completely. Close the drain valve and remove the hose once the water heater is empty. Turn the power or gas supply back on and refill the water heater before turning it back on.


What is the proper procedure for maintaining and cleaning a water heater drain pipe?

To maintain and clean a water heater drain pipe, follow these steps: First, turn off the water heater and let it cool. Next, locate the drain valve at the bottom of the heater and attach a hose to it. Place the other end of the hose in a drain or outside. Open the valve to drain the water heater. Once empty, close the valve and flush the tank with clean water. Finally, close the valve, refill the tank, and turn the water heater back on.


How can I effectively drain hot water heater sediment?

To effectively drain hot water heater sediment, follow these steps: Turn off the heater, connect a hose to the drain valve, place the other end of the hose in a drain or outside, open the valve to release the water and sediment, close the valve once the water runs clear, and finally, turn the heater back on. Regularly draining sediment helps maintain the heater's efficiency and prolong its lifespan.


How do I properly maintain and clean a water heater drain hose?

To properly maintain and clean a water heater drain hose, you should regularly inspect it for any clogs or debris. To clean it, disconnect the hose and flush it out with water to remove any buildup. Make sure to reattach the hose securely after cleaning to prevent leaks.


How do you drain water from 40 gallon hot water heater in my house?

At the bottom front edge, there should be a hose connection. Attach a garden hose to it and then open the valve. Because sediment can collect at the bottom of the heater, they can drain slow sometimes, but it should drain eventually. Turn the heater off before draining.


How can I effectively drain sediment from my hot water heater?

To effectively drain sediment from your hot water heater, follow these steps: Turn off the heater, connect a hose to the drain valve, place the other end of the hose in a safe drainage area, open the valve to release the water and sediment, and repeat until the water runs clear. This process helps maintain the heater's efficiency and prolong its lifespan.


How do you properly drain a tankless water heater?

To properly drain a tankless water heater, first turn off the power and water supply. Connect a hose to the drain valve and place the other end in a suitable drainage area. Open the valve and let the water drain completely. Close the valve, remove the hose, and turn the water supply back on.


How to drain and flush a water heater effectively?

To drain and flush a water heater effectively, follow these steps: Turn off the power or gas supply to the water heater. Connect a garden hose to the drain valve at the bottom of the water heater. Place the other end of the hose in a safe drainage area, like a floor drain or outside. Open the pressure relief valve on the water heater to allow air in and help with draining. Open the drain valve and let the water heater drain completely. Close the drain valve and remove the hose. Fill the water heater with cold water to flush out any remaining sediment. Repeat the draining process if necessary until the water runs clear. Close the pressure relief valve and refill the water heater. Turn the power or gas supply back on and monitor the water heater for any leaks. Remember to follow the manufacturer's instructions and safety precautions when draining and flushing your water heater.


How to drain and flush a water heater properly?

To drain and flush a water heater properly, follow these steps: Turn off the power or gas supply to the water heater. Connect a garden hose to the drain valve at the bottom of the water heater. Place the other end of the hose in a safe drainage area, like a floor drain or outside. Open the pressure relief valve on the water heater to allow air in and help with draining. Open the drain valve and let the water heater drain completely. Close the drain valve and remove the hose. Fill the water heater with cold water to flush out any remaining sediment. Repeat the draining process if necessary until the water runs clear. Close the pressure relief valve and refill the water heater. Turn the power or gas supply back on and monitor the water heater for any leaks. Remember to follow the manufacturer's instructions and safety precautions when draining and flushing your water heater.


How to effectively drain water heater sediment for optimal performance and longevity?

To effectively drain water heater sediment for optimal performance and longevity, follow these steps: Turn off the power or gas supply to the water heater. Allow the water heater to cool down. Connect a garden hose to the drain valve at the bottom of the water heater. Place the other end of the hose in a drain or outside. Open the pressure relief valve on the water heater. Open the drain valve and let the water heater drain completely. Close the drain valve and pressure relief valve. Turn the power or gas supply back on. Repeat this process every 6-12 months to prevent sediment buildup and maintain optimal performance and longevity of the water heater.


How to properly flush an electric water heater for optimal performance and longevity?

To properly flush an electric water heater for optimal performance and longevity, follow these steps: Turn off the power to the water heater. Connect a garden hose to the drain valve at the bottom of the heater. Place the other end of the hose in a drain or outside. Open a hot water faucet in the house to allow air into the system. Open the drain valve and let the water heater drain completely. Close the drain valve and refill the tank. Turn the power back on and monitor the heater for any leaks. Flushing the water heater removes sediment and mineral buildup, improving efficiency and extending its lifespan.