answersLogoWhite

0

When installing things like shower doors, although you can do it yourself, I would suggest getting the help of a professional. This is because you want to be sure that it has been installed securely, and they will have more experience than you in installing it.

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Engineering

Why would ceramic tile pop up a week after being installed?

it could be a number of things, premixed thinset, to much flex in the substrate, mixed thinset too thin, didnt seal grout "if in shower" where is the tile installed, what did you use to install it and how did you install it?


Can you install a shower vent from the inside on third floor?

Yes, you can install a shower vent from the inside on the third floor, but it requires careful planning. You'll need to ensure that the vent duct can run straight to the exterior or through appropriate pathways without obstruction. It's also important to comply with local building codes and regulations regarding ventilation systems. If you're unsure, consulting a professional plumber or contractor is advisable.


Which is more correct take a shower or have a shower?

To take a shower is US English; to have a shower is UK English.So they are both correct.


Is there a way to cut and re-thread a shower pipe that is already coming out of the wall?

You Can but typically the pipe for the shower head that is coming out of the wall is just a short piece of pipe that you should be able to remove easily enough by unscrewing it. Then you can just replace that piece with a new one. == Answer== Do the same as above but make sure your shower arm is not floppy, if it is you could tear up the riser coming to the arm. Be very carefull.


What is a valve trim?

That is the handles, screws, face plate and everything except the rough in valve. The rough in is the main body of the valve that is installed in the wall before drywalling or putting the tub/shower in. The trim is put on after the walls are finished.

Related Questions

Can you install a walk in shower without hiring a professional?

Walk in shower stalls are moderately difficult to install. Pre fab shower stalls are already built for you and only need to be installed. Unless you are an expert it is highly recommended to hire a licensed plumber to get the plumbing set up before installing your shower.


What tools does one need to install a handicap shower stall?

The tools that are needed to install a bathroom shower are measuring tape, spanners, tile drill, dust sheets, pencil, and pipe cutters. It is best to engage a professional shower fitter to fit one's bathroom shower, instead of DIY project.


New shower installed the hot and cold won't mix What do I do?

Call a professional so someone does not get scalded


Where can I find a shower soap holder that can be easily installed on a tile wall?

You can find a shower soap holder that can be easily installed on a tile wall at most home improvement stores or online retailers. Look for options that come with adhesive or suction cup attachments for simple installation.


Can a Bobrick shower curtain rod be installed in the ceiling instead of the shower walls?

The Bobrick shower curtain cannot be installed in the ceiling. It is made be installed in the shower wall brackets.


Can I put a Double Crescent shower rod into my standard shower?

Because these shower rods are customizable for length, they can be installed into any standard shower.


Where should shower grab bars be installed for optimal safety and accessibility?

Shower grab bars should be installed vertically near the entrance of the shower, horizontally along the back wall, and diagonally near the shower seat for optimal safety and accessibility.


what is the cheapest price i could buy a walk in tub shower for?

Prices for walk-in shower/tubs vary. Usually they need to be installed by a professional so that will make the cost a little higher. This site http://envywalkintubs.com/ has them starting at $1899 which is not a bad price.


How much does it cost to have a shower tray installed?

The cost to have a shower tray installed ill depend on the type of tray you choose. You can expect to pay about $20 per hoor for the labor.


What should I do if my brand new shower head is leaking?

If your brand new shower head is leaking, you should first check if it is properly installed and tightened. If it continues to leak, you may need to replace the shower head or its components. If the issue persists, consider contacting the manufacturer for assistance or seeking help from a professional plumber.


When to Have a New Shower Installed?

There are a lot of shower installations out there that were done in a time when efficiency was not the order of the day. Because of this, many showers out there use way too much water, and allow way too much water to spill out of shower doors. Generally, if your shower was installed before you bought your home then you may want to consider getting a new shower installed. If you rent, ask how old the shower is and see if you can work something out with your landlord to have a new one installed. Old showers can also hold serious levels of mold, so be careful.


Where should grab bars be installed in a shower for optimal safety and accessibility?

Grab bars should be installed vertically near the entrance of the shower, horizontally along the back wall, and diagonally near the shower seat for optimal safety and accessibility.