answersLogoWhite

0

I have had it like that at a house I lived at, it would drain directly into the basement floor drain, however it was a pain in the behind, because I often found myself tripping over it, or if the kiddos wanted to ride their bikes or 3 wheeler toddler things in the basement they would get hooked up on the hose also. And if it got to far away from the floor drain I had a water mess, so if at all possible go with the drain behind washer, out of sight ... out of mind.

User Avatar

Wiki User

15y ago

What else can I help you with?

Continue Learning about Engineering

How do you lower the water level in my boilers sight tube its too high im not getting enough heat to my second floor?

There should be a drain valve on the boiler. Drain it to the desired water level there.


How do you slope a floor to a drain?

To slope a floor to a drain, first determine the drain's location and the required slope, typically 1-2% (1/8 to 1/4 inch per foot). Mark reference lines on the floor using a level or chalk line to ensure a consistent slope towards the drain. Then, adjust the subfloor or pour a sloped layer of concrete or mortar, ensuring that the high point is away from the drain and gradually lowers toward it. Finally, finish the surface to ensure proper drainage and a smooth transition.


What is The level between ground floor and first floor?

mezzanine


How do you level a floor with a drain?

Prior to caulking the lead joint I use a level then pour the joint and tap each side of the lead so the drain does not shift then finish packing the lead and trim the lead with a trimming iron...same as for CI roof drains except roof drains are slightly counter sunk to allow for the 4 PSF sheet lead flashing


What is the odds of a leak when using 2 wax rings one with flange and with out?

Should be zero, but it happens. You usually use two rings when the drain is below the level of the floor. If you put ceramic tile down this happens. As long as the wax seals against the toilet and the floor, it shouldn't leak. Another issue is if the drain sticks above the floor too much and the toilet tends to rock on the drain. This will cause a leak. You set the toilet in place and put your weight on it to compress the seal and tightened the mounting bolts snug? You can use two rings both with flanges. That way there shouldn't be a side blowout.

Related Questions

Why does the washing machine drain overflow?

The washing machine drain may overflow due to a clog in the drain pipe, a malfunctioning pump, or an issue with the machine's water level sensor.


What is the optimal height for a washing machine drain?

The optimal height for a washing machine drain is typically between 30 to 36 inches above the floor level. This height helps to ensure proper drainage and prevent issues such as backflow or clogs.


Why does my washing machine drain overflow?

Your washing machine drain may overflow due to a clog in the drain pipe, a malfunctioning pump, or an issue with the machine's water level sensor. It is important to check and address these potential causes to prevent further overflow.


What is the recommended washing machine drain height for optimal performance and efficiency?

The recommended washing machine drain height for optimal performance and efficiency is typically around 30 inches above the floor level. This height helps to prevent water from backing up and ensures proper drainage during the wash cycle.


What is the recommended height for a washing machine standpipe?

The recommended height for a washing machine standpipe is typically around 36 inches above the floor level.


How can I properly install a washing machine drain pan to prevent leaks and water damage?

To properly install a washing machine drain pan to prevent leaks and water damage, follow these steps: Place the drain pan under the washing machine. Connect the drain hose to the pan's outlet. Ensure the pan is level to prevent water from spilling. Test the washing machine to check for leaks. Regularly inspect and clean the drain pan to prevent clogs.


How can I ensure a proper washing machine connection is established in my home?

To ensure a proper washing machine connection in your home, follow these steps: Check that the water supply lines are connected securely to the washing machine. Make sure the drain hose is properly connected to the drainage system. Ensure the washing machine is level and stable on the floor. Test the connections by running a small cycle to check for leaks or issues.


What is the washing machine drain code for proper installation and maintenance?

The washing machine drain code for proper installation and maintenance typically requires the drain hose to be secured above the level of the washing machine and to have a P-trap to prevent backflow. Regular cleaning of the drain hose and P-trap is also recommended to prevent clogs and ensure proper drainage.


How do you level your washing machine?

To level your washing machine, first ensure it is unplugged. Use a level to check that the machine is resting evenly on the floor. If not, adjust the machine's feet by turning them clockwise to raise the corner and counterclockwise to lower it until the machine is level. Recheck with the level and adjust as needed.


How do you level an Amana washing machine?

Most washing machines, including the Amana washing machine, have screws on the bottom with little pads that can adjusted to level the washer. Use a floor jack to lift up the washer and turn out one or more of the feet. Then check the level.


What is the recommended height for the p-trap of a washing machine?

The recommended height for the p-trap of a washing machine is typically between 6 to 18 inches above the floor level.


What are effective solutions for dealing with a washing machine drain overflow?

To address a washing machine drain overflow, you can try these effective solutions: Check for clogs in the drain hose and remove any blockages. Ensure the drain hose is properly installed and not kinked. Use a drain snake or plunger to clear any obstructions in the drain pipe. Adjust the water level settings on the washing machine to prevent overflows. Consider installing a drain pan or overflow sensor to prevent future issues.