answersLogoWhite

0

Yes if the vent pipe is 4" and vertical by code and there is nothing connected between your toilet tee and where you would connect your new toilet tee. If not worried about codes then yes you can connect to a 3" vent line if no other vent lines are connected down stream. If you have a vent pipe that is less then 3" and or you have other vents connected between your old toilet tee and your new toilet tee then NO you can not connect a new tee for your toilet.

User Avatar

Wiki User

14y ago

What else can I help you with?

Continue Learning about Engineering

Do you need to vent a new toilet in a basement if it is connected to a 3-inch pipe that has other toilets on the floors above connected to it?

Yes. If not it will be a wet vent and cause MAJOR problems.


When adding another toilet 6 feet from an existing toilet do you need a new vent and would 3-inch pipe be sufficient?

where one toilet is draining to its own unshared line, the line can be 3" but once both toilets are draining to the same line, it needs to be 4". in other words, from the first toilet to the second toilet can be 3" but past the second toilet needs to be 4". there needs to be a vent downstream of the second toilet in the direction of flow if there is another fixture of any kind downstream of the two toilets.


How do you add and additional bathroom when you have a slab floor?

You will either have to break up the concrete to tie into the under-slab main waste pipe, or you will need to build a subfloor high enough to run the drain pipes underneath, and then connect into the main drain above grade. Keep in mind that you will need some amount of fall (slope) on the pipe, and that you will also need to tie in to the vent stack, or run a new vent through the roof. This should be 4"ABS for a toilet, and 1 1/2" - 2"ABS for a sink or shower.


Can you connect sink waste vertically into horizontal pipe that exits rear of toilet at side of proposed new sink location.?

You can, I'm not sure that I would. Probably doesn't pass code for one thing. If that is not an issue, that is the main stack. Down to the sewer, up to the roof vent. If you attach a sink drain there, when the toilet is flushed, it will pull venting from wherever it can. Most will still come down from the roof, but being as close as it is, it will also pull from the sink drain and cause a gurgling from the sink. The other consideration is the sink itself. Make sure it has an overflow vent in the rim of the sink. If the one you use doesn't the drain will need a vent of its own, otherwise the sink drain will be trying to pull against a vacuum. Another thought. They make what is called a Saddle Clamp to do what you are talking about. A half piece of pipe with a female connection in the side of it. Made of PVC and held on with two clamps that go around the existing pipe.


Why is water coming out of toilet bolts?

You need a new wax ring.

Related Questions

Do you need to vent a new toilet in a basement if it is connected to a 3-inch pipe that has other toilets on the floors above connected to it?

Yes. If not it will be a wet vent and cause MAJOR problems.


Should sink waste pipe be connected to toilet waste pipe?

The short answer is yes, but like all answers comes with conditions. In a traditional residential plumbing system all drain lines eventually connect together, everything is interconnected.The long answer is that connecting fixtures to a drain system must follow certain rules and good practices which have been proven over time. Assuming you have a rudimentary knowledge of plumbing systems you may proceed with the following.You may connect to your horizontal toilet waste pipe but should be 3-5 pipe diameters downstream any vertical portion (like where it turns up to the toilet, or turns to go up a wall for an upstairs toilet.) If you do connect to a horizontal portion the new pipe must be sized to serve as both a drain (for the new fixture) and as a vent (for both the new fixture and the toilet.) this means that the new drain must connect back into the vent system (at least 6" higher than the rim of the highest fixture connecting to that system) OR must vent separately out the roof of the building or through an approved air admittance device. (basically an air valve in the cabinet or wall space that lets air into the system but not out. - -air valves have special provisions and are tricky so research them thoroughly before installing one.)You may also connect to a vertical stack. (a large pipe serving fixtures on the floor above) When connecting to a stack you need only size the new pipe to serve as a drain and vent for the new fixture. Generally you may connect to any portion of the vertical stack (high or low) as long as you use a wye branch fitting or other approved drainage pattern fitting. hope this helps.


What size went is needed on the toilet drain?

2" VENT. Many codes say the vent can be 1/2 the size of the pipe being served but in no case less then 11/2" and considering a lead bend (toilet drain) can be 3" and the new fixtures have 1.6 GPF in lieu of the 3.5 GPF a 11/2 vent pipe is fine


When adding another toilet 6 feet from an existing toilet do you need a new vent and would 3-inch pipe be sufficient?

where one toilet is draining to its own unshared line, the line can be 3" but once both toilets are draining to the same line, it needs to be 4". in other words, from the first toilet to the second toilet can be 3" but past the second toilet needs to be 4". there needs to be a vent downstream of the second toilet in the direction of flow if there is another fixture of any kind downstream of the two toilets.


What size pipe do I need for my new toilet?

Normally 11/2" vent and a 3" soil line=BUT some codes want a 4" waste and then a 2" vent may be required depends on the local inspector=


Why wont wolfquest connect?

your computer is older and wolf quest is a new progress


How do I install a new toilet flange?

To install a new toilet flange, first remove the old flange and clean the area. Place the new flange over the drain pipe and secure it with screws. Make sure it is level and properly aligned. Finally, connect the toilet to the flange and secure it in place.


How do I properly install a new toilet flange?

To properly install a new toilet flange, first remove the old flange and clean the area. Place the new flange over the drain pipe and secure it with screws. Make sure it is level and flush with the floor. Finally, connect the toilet to the flange using a wax ring and bolts, then secure the toilet in place.


What are the necessary steps for relocating a dryer vent in a home?

To relocate a dryer vent in a home, follow these steps: Determine the new location for the vent, ensuring it meets building codes and is easily accessible. Turn off the power to the dryer and disconnect the vent pipe from the dryer. Remove the existing vent pipe from the wall or ceiling. Install a new vent pipe in the desired location, making sure it is properly sealed and secured. Connect the new vent pipe to the dryer and ensure it is properly aligned. Test the dryer to ensure proper ventilation and functionality.


How can I install a toilet in my bathroom?

To install a toilet in your bathroom, first turn off the water supply and remove the old toilet. Place a new wax ring on the flange, then carefully lower the new toilet onto the flange and secure it in place with bolts. Connect the water supply line and tighten the connections. Finally, test the toilet for leaks and make any necessary adjustments.


Can I place a shower where a toilet currently is and visa versa and are waste sizes the same and if so can I connect new stack to existing in attic?

The toilet is 3 or 4 inch and the shower is 1 1/2 or 2 inch. You could reduce the toilet to 2 inch, but it would never flush correctly or be of much use. The current toilet drain has no trap in that section because one isn't needed. The toilet itself is the trap. If you are using existing waste lines, they should already be connected to the vent stack. If you are adding lines, connecting to the existing stack is fine as long as it is above the last drain.


What is different from old toilets to new toilets?

The biggest difference from an old toilet to a new one is the water consumption. An older toilet can use up to 16L of water per flush! A modern toilet only uses between 3-5L per flush. A big money saver!