0
Cutting a pre-tensioned slab is generally not advisable without expert guidance, as it can compromise the structural integrity and safety of the slab. Pre-tensioned concrete is designed to withstand specific loads, and cutting it may release built-up stresses, leading to cracking or failure. If modifications are necessary, it's crucial to consult with a structural engineer to assess the situation and recommend appropriate methods. Proper techniques and precautions must be followed to ensure safety and stability.
What else can I help you with?
What should you do if the lap for steel reinforcement is to short but is already in concerete?
Drill out the edge of the slab and add some dowels....or cut the slab back.
How do you take pipe from sunk slab?
To take a pipe from a sunk slab, first, ensure the area is safe and well-ventilated. Use appropriate tools to carefully cut around the pipe, avoiding damage to the slab or surrounding structures. Once the pipe is exposed, disconnect it from any fittings or connections, and then remove it from the slab. Finally, seal any openings in the slab to prevent moisture intrusion or other issues.
How do you remove a concrete slab?
You have to break it with a sledge hammer , cut it, dynamite it, dig it up or lift it up with a fork lift or caterpiller.
How thick should a 30' x 40' concrete slab be?
4". A 4" thick concrete slab reinforced with 6 x 6 x 10 welded wire mesh placed over a 6 ml vapor barrier on 6" of levelled and compacted gravel or sand is common for many residential applications. I'm assuming there are no point loads anywhere in the slab interior and the slab is used for general purposes such as a residential basement, workshop, or garage floor. Any special circumstances should be engineered. All steps in the process are important, but one often overlooked is that the base needs to be properly compacted and prepared. A good base will be very level and very well-compacted. If the base is poor, the slab may need to be thicker or engineered. Slabs will crack where the thickness changes and stress forces become concentrated while it's curing and then while it's settling. If you have posts coming down anywhere in the field of the slab, be sure to cut control joints around them and across the slab to direct the inevitable cracks during curing and settling. Control joints are best when they are saw-cut to 1/3 the depth of the slab after the slab has set, and generally spaced 10-12' apart is good. Trowelled-in control joints do not work nearly as well as saw-cut. Also, remember to use an isolation material such as conventional felt strips at the slab edge to prevent mechanical bonding to adjacent walls and allow for slight differential movement.
Definition of a concrete transfer slab?
what is a ytransfer slab
What is slab work using clay?
A slab of clay is a flat piece of clay rolled out. With a slab of clay, it is much easier to cut/trace things.
Is it safe to cut slab for connecting 2 flats?
It really depends on the base structure and the legal rights. Who owns the slab? Is it providing structural support of some nature? Do you need access to both sides to accomplish the work? If so, will the other party agree to access? If the economic value of either property impacted if the slab was cut or otherwise changed? Does the cut need to be sealed or otherwise treated after a cut to protect the slab and the possible steel in the concrete?
What is a ceramic project called when a flattened piece of clay cut out?
Slab
What should you do if the lap for steel reinforcement is to short but is already in concerete?
Drill out the edge of the slab and add some dowels....or cut the slab back.
What is the slab method in pottery?
The clay is rolled out like pastry into a flat slab. Then these slabs are cut, joined, curved and shaped to form the pot.
Can you cut a exiting slab?
Yes. Its expensive. Most people will cut an inch or so with a saw then jack hammer it out.
Can you use a cattle salt block cut to a 2 inch slab to cook with?
yes
Can a torch make a rough cut on a marble slab?
No. you don't cut stone with fire. That is just plain stupid. You cut marble with diamond tipped blades or with water jets.
How do you take pipe from sunk slab?
To take a pipe from a sunk slab, first, ensure the area is safe and well-ventilated. Use appropriate tools to carefully cut around the pipe, avoiding damage to the slab or surrounding structures. Once the pipe is exposed, disconnect it from any fittings or connections, and then remove it from the slab. Finally, seal any openings in the slab to prevent moisture intrusion or other issues.
What is supreme cut of fish?
A supreme is a slice cut off a fillet, sometimes cut at a slant.This cut is now commonly called a pavé which means 'a slab or block' and usually applied to cake or dessert - but now is fashionably applied to fish!
How many ribs in a full slab?
A full slab of ribs typically consists of 13 ribs, which are usually taken from the pork spareribs or baby back ribs. The exact number can vary slightly depending on how the slab is cut, but a full slab generally contains these 13 ribs. In some cases, beef ribs may also be served in slabs, but the standard reference is for pork ribs.
What difference suspended concrete slab between unsuspended concrete slab?
Supended slab are slab not sit on the ground directlySuspended slab is a slab supported by beams.
