0
You must remove the old epoxy coating before pouring the new floor, for otherwise there will be no bonding. If the epoxy coating is thin (e.g, paint) then it may be possible to remove it by hand sanding. If it is a thick coating, then sandblasting is probably the best method. In either case, appropriate dustmasks and other safety precautions are essential. Good luck
What else can I help you with?
Can I pour 4in of concrete on an existing concrete floor indoors that will be carpeted?
Yes. I would use a peagravel mixture with fibermesh additive. Pressure wash the area first if possible.
How much does it cost to pour a concrete driveway?
how much does it cost to form and pour concrete in Mobile, AL
How much to pour a concrete slab 12x24?
about how much to pour a concrete slaba 12 x 14'
How do you build a floor on sloping concrete?
it can be done == you can pour self leveling cement mixture over old concrete but you must first rough up surface of old concrete then put bonding agent then mix self leveling mix very wet so you can pour from high spot and it will run to lower areas . Use wood furring strips ripped at an angle to compensate for the angle in the sloped concrete.
Can you pour a concrete slab onto another concrete slab?
No. Concrete won't bond to concrete. It will end up cracking.
Can you pour epoxy over polyurethane for a smooth and durable finish?
No, it is not recommended to pour epoxy over polyurethane for a smooth and durable finish.
How can I embed pictures in epoxy to create a unique and personalized item?
To embed pictures in epoxy to create a unique and personalized item, first prepare the picture by printing it on waterproof paper or coating it with a waterproof sealant. Then, pour a layer of epoxy into a mold, place the picture on top, and cover it with another layer of epoxy. Allow it to cure according to the epoxy's instructions. Sand and polish the surface for a smooth finish.
What is a monolithic pour?
A pour of concrete, all at a single time. Also called a one-pour system. Contrast with two-pour system. At the same time you pour the floor, you are going to pour the perimeter footings. This is called a monolithic pour (or monolithic slab).
How to properly prepare and pour a concrete floor?
To properly prepare and pour a concrete floor, follow these steps: Prepare the site by clearing and leveling the area, ensuring proper drainage. Install a vapor barrier to prevent moisture from seeping into the concrete. Build forms to contain the concrete and provide a guide for pouring. Mix the concrete according to the manufacturer's instructions. Pour the concrete evenly into the forms, using a screed to level and smooth the surface. Use a bull float to further smooth and level the concrete. Allow the concrete to cure for the recommended time before removing the forms and finishing the surface as desired.
How can I achieve a professional finish on my table with an epoxy table top coating?
To achieve a professional finish on your table with an epoxy table top coating, follow these steps: Prepare the surface by sanding and cleaning it thoroughly. Apply a primer to ensure good adhesion of the epoxy. Mix the epoxy according to the manufacturer's instructions. Pour the epoxy onto the table and spread it evenly with a spreader or brush. Use a heat gun or torch to remove any air bubbles. Allow the epoxy to cure according to the recommended time. Sand the surface lightly to remove any imperfections. Apply a top coat for added protection and shine.
What is the average cost PER square foot for a concrete floor for factory?
It would depend on where you purchase the concrete, and the brand you purchase, and whether you pour the floor yourself or have it done and pay labor.
How can I properly install an epoxy floor over plywood?
To properly install an epoxy floor over plywood, follow these steps: Ensure the plywood is clean, dry, and free of any debris. Sand the plywood to create a rough surface for better adhesion. Apply a primer specifically designed for epoxy flooring. Mix the epoxy resin and hardener according to the manufacturer's instructions. Pour the epoxy mixture onto the plywood and spread it evenly with a roller. Allow the epoxy to cure according to the recommended drying time. Apply a topcoat for added protection and durability.
Can I pour 4in of concrete on an existing concrete floor indoors that will be carpeted?
Yes. I would use a peagravel mixture with fibermesh additive. Pressure wash the area first if possible.
How can I create a DIY concrete floor in my home?
To create a DIY concrete floor in your home, you will need to prepare the area by cleaning and leveling the surface. Then, mix concrete according to the instructions on the bag and pour it onto the floor. Use a trowel to spread and smooth the concrete evenly. Allow it to dry and cure properly before walking on it. Optional steps include adding color or a sealant for a finished look.
How much concrete do you need to pour in a floor measuring 28 feet wide 72 feet long and 6 inches deep?
you would need 37.33 yards of concrete or 38 to be safe
How much does it cost to pour a concrete driveway?
how much does it cost to form and pour concrete in Mobile, AL
Can you pour polyurethane like epoxy for a resin art project?
No, polyurethane cannot be poured like epoxy for a resin art project.
