answersLogoWhite

0

What else can I help you with?

Continue Learning about Engineering

Is it necessary to put teflon on the threads of shower valves?

Since water can leak through the smallest cracks and holes, applying a clockwise layer or two of teflon tape to the threads of a plumbing connection can help prevent water leakage.


What is the correct way to apply Teflon tape to a threaded piece of steel pipe?

First, make sure the pipe threads are clean and in good condition. Hold the end of the tape flat against the pipe threads, flush with the end of the pipe, then turn the pipe clockwise, or as though you were tightening it. Put 1-1/2 to 2 turns of tape on the pipe, keeping the tape flat and tight against the pipe as you turn, then thread the pipe immediately into the fitting. The reason for doing it this way is so the loose end gets pinned down by the action of screwing the pipe in, rather than getting flipped up.


What should you do if you have tiled tub surround and the faucet pipe is too short and you can put the faucet back on but it will just turn a couple of times and is not tight enough to prevent leaking?

Examine the pipe, you can probably turn it out using a pipe wrench, and replace the pipe with one that is 1/2 inch longer. Alternatively, if you can get a couple turns on the pipe, just wrap some teflon tape around the pipe and see if that stops the leak.AnswerI would change out nipple to longer one, and then get a new Delta spout with brass adap. When you install spout it will go back to tile all the way. I think if you added .5in. nipple it would make it to long, then it would not go to tile wall all the way. Or do the teflon tape around pipe and see what happens. ANS 3 - The piece of pipe sticking out of the wall is a 'nipple', unscrew it with a pipe wrench, measure it and get on 1/2 inch longer, put pipe compound or thread tape on the end and screw it into the fitting . Now re-fit your faucet.


How much pressure does it take to put on a fan belt?

On what?


How much weight can you put on a leach field?

None.

Related Questions

How do you put on Teflon tape correctly?

To put on Teflon tape correctly, wrap the tape around the threads of the pipe in a clockwise direction. Make sure to overlap the tape by half its width with each wrap. This will create a tight seal and prevent leaks.


How to put Teflon tape on effectively?

To put Teflon tape on effectively, start by wrapping the tape around the threads of the pipe in the direction of the threads. Make sure to wrap the tape tightly and evenly, overlapping each layer slightly. Be sure to wrap the tape at least three times around the threads to create a tight seal. Cut the tape cleanly with scissors once you have wrapped it around the threads. This will help prevent leaks and ensure a secure connection.


Can you use Teflon tape on fuel rail fittings for a 1999 Chevy Malibu?

yes you just have to make sure you put the tape the same direction as the threads. Also be careful not to have the tape before the threads or you will get particles in your fuel system.


Is it necessary to put teflon on the threads of shower valves?

Since water can leak through the smallest cracks and holes, applying a clockwise layer or two of teflon tape to the threads of a plumbing connection can help prevent water leakage.


How do you stop hot water relief valve from leaking around threads on new installation?

You have to use pipe dope or Teflon tape on the threads before you put it together. Pipe dope should fill the threads and if tape is used, 3-4 layers of tape should be enough.


What could be wrong if your shower head leaks after completely removing the head?

Put teflon tape on the threads. 6 or 7 turns will do fine


How do you put on thread tape correctly?

To put on thread tape correctly, start by wrapping the tape around the male threads in the direction of the threads. Make sure to wrap the tape tightly and evenly, overlapping each layer slightly. Trim any excess tape and then screw the male and female threads together firmly. This will create a tight seal and prevent leaks.


Can you put a metal fitting on a plastic pipe?

yes you can put a metal fitting on a plastic pipe but it is not highly recommended but if you must use it make sure that you wrap both fittings with teflon tape in the opposite direction of the threads and be sure not to tighten to to tight this will cause the plastic to bust i hope this has helped


How do you put on plumber's tape correctly?

To put on plumber's tape correctly, start by wrapping the tape clockwise around the threads of the pipe. Make sure to overlap the tape slightly as you go. Tighten the connection securely to prevent leaks.


Do you use PVC pipe cement when connecting a PVC pipe to a galvanized metal pipe?

No, do not use glue. Use teflon tape or pipe dope on the threads. You should also make sure you always put the male PVC thread into the female metal thread. If you do it the other way you will tend to split the PVC fitting when you tighten the threads.


Can you apply heat to teflon tape to solder a copper joint?

Yes, you can. I had this very same question myself a few days ago. In order to answer it, I put a piece of teflon tape in the flame of a propane torch. It shriveled, but did not burn or melt and when I stretched it out, it returned to its original shape. I then made a sweat joint inches from a teflon wrapped joint with no problems. You sure want to be carfeul when doing this though. Teflon gives off extremely toxic gas if you melt it.


What is the correct way to apply Teflon tape to a threaded piece of steel pipe?

First, make sure the pipe threads are clean and in good condition. Hold the end of the tape flat against the pipe threads, flush with the end of the pipe, then turn the pipe clockwise, or as though you were tightening it. Put 1-1/2 to 2 turns of tape on the pipe, keeping the tape flat and tight against the pipe as you turn, then thread the pipe immediately into the fitting. The reason for doing it this way is so the loose end gets pinned down by the action of screwing the pipe in, rather than getting flipped up.