0
It will depend on the application. If you are trying to rapair some thing which as per design needs 470uF capacitor but you only have 100uF capacitors available., you can put 5 of these in parallel if possible (if SMD you can put one on top of another and solder). That will give you a total of 500uF close to the original value.
- Neeraj Sharma
What else can I help you with?
Would it be ok to rplace the 25v 680 uf capacitor with a 25v 1000 uf on a xboard in a lcd tv?
Yes, you can replace a 25V 680µF capacitor with a 25V 1000µF capacitor in an LCD TV, as long as the voltage rating is the same or higher. The increased capacitance means the new capacitor can store more charge, potentially improving stability in some circuits. However, ensure that the physical size fits and that the circuit can handle the larger capacitance without adversely affecting performance. If in doubt, consult the device's specifications or a professional.
Can you replace 2200 uf 24 volt capacitor with a 2200 uf 16 volt capacitor?
NO dont do it if you devalue a capacitors voltage parameter what will it do when it is face to face with 20V ? The voltage will destroy the thing. Remember it is OK for you to use a higher voltage parameter for a capacitor but never lower
What is the difference between a 47uf 50 v capacitor and a 47uf 25v capacitor for a tattoo machine?
A: It may tattoo your face when it blow up if the 25 volts is used where a 50 volts should be, you may substitute 47 mfd 500 volts for the 50volts cap and the 25 volts cap But you cannot substitute 15 volts for the 25 volts capacitor
How 70V 25V 8-ohm and 4-ohm speaker loads works?
In a 70V distributed audio system, amplifiers output audio signals at a higher voltage (70V) to allow for longer cable runs with reduced signal loss and the ability to connect multiple speakers in parallel. The 25V system operates similarly but is used for shorter distances and fewer speakers. Speakers rated at 8-ohms or 4-ohms can be connected to the system using transformers that match their impedance to the 70V or 25V lines, ensuring efficient power transfer and sound quality. In both cases, the transformer allows for multiple speaker loads to be connected without overloading the amplifier.
Why rs232 voltage level converting to ttl level?
RS-232 is a standard built a longer while ago, and its specifications dictate a maximum voltage of +-25V. HIGH signal levels at +-5V, +-12V and +-15V are not uncommon. The range of operation is from -25V to +25V. Also, RS-232 standard notes that levels between -3V and +3V are illegal (as in, they are assumed not to exist, nor carry any information). On the other hand, TTL stands for Transistor-Transistor Logic, and the maximum rating for that is 5V. HIGH signal levels are at any point above 3.5V. The range of operation is between 0V and 5V. If one were to connect these with no conversion, the TTL device would probably be burned. Even if it would withstand, the designs are sufficiently different for them not to communicate properly. Thus, the need to 'bridge the gap' between the two.
Can you replace a 470uf 10v capacitor with a 470 25v 105c high temp radial leads capacitor for a digital tv converter box?
Yes, as long as there is room to mount the larger capacitor. A better replacement might be a 470uF 16v capacitor, which should be smaller than the 25v cap. If necessary, insulating tubing can be put on the leads & the cap can be mounted off the board, or at an angle to the board. Remember to observe polarity when connecting the capacitor leads to the board. Note the orientation & markings on the old capacitor before unsoldering it.
Would it be ok to rplace the 25v 680 uf capacitor with a 25v 1000 uf on a xboard in a lcd tv?
Yes, you can replace a 25V 680µF capacitor with a 25V 1000µF capacitor in an LCD TV, as long as the voltage rating is the same or higher. The increased capacitance means the new capacitor can store more charge, potentially improving stability in some circuits. However, ensure that the physical size fits and that the circuit can handle the larger capacitance without adversely affecting performance. If in doubt, consult the device's specifications or a professional.
Can a capacitor in a lcd television be changed if cant find exact numbers eg 220 25v instead of 220 16v and what would change be?
Yes, the higher voltage is not only OK, but is desirable, as it will be longer-lasting. It is very important to replace the capacitor with the same type. If it is a ceramic disk, replace it with a ceramic disc. If it is metal-film, then replace it with a metal-film capacitor, and so on.
Can you replace 2200 uf 24 volt capacitor with a 2200 uf 16 volt capacitor?
NO dont do it if you devalue a capacitors voltage parameter what will it do when it is face to face with 20V ? The voltage will destroy the thing. Remember it is OK for you to use a higher voltage parameter for a capacitor but never lower
What is the difference between a 47uf 50 v capacitor and a 47uf 25v capacitor for a tattoo machine?
A: It may tattoo your face when it blow up if the 25 volts is used where a 50 volts should be, you may substitute 47 mfd 500 volts for the 50volts cap and the 25 volts cap But you cannot substitute 15 volts for the 25 volts capacitor
Can i replace a 1000uf 10v capacitor with a 1000uf 25v capacitor?
in a psu a general yes but the peek load with go up on the diodes before it you could go for a 47uF and the peek load with go down but you might get some hum.. if it is the start up cct from a switch mode and the thing starts with a 100uF or a 47uF then fine.. you can get 68uF 50V caps from some suppliers. and in any case the tolerances on these caps is + or - 20% ish anyway.. hope this helps.. Simple answer,,,Yes, you can.
Can you replace a 40v light bulb with a 25v one?
No, it is not recommended to replace a 40v light bulb with a 25v one. The voltage rating of the bulb should match with the voltage of the electrical circuit to ensure proper operation and prevent damage. Using a bulb with a lower voltage rating can cause it to burn out quickly or potentially create a safety hazard.
What is the factor of 25v plus 19v plus 4?
That's 44v + 4 which factors to 4(11v + 1)
How work ic 7805 and his constrction?
1. connect pin #1 to source (input voltage), pin #3 to the load (output), pin #2 to ground. 2. at the input 100 uF electrolytic capacitor, at least 25V (the higher capacitance is better, its to make sure that the source will provide the energy for prompt consumption from the 7805 regulator 3 At the ouput connect 0.1uF ceramic capacitor (for noise filtering) and in parallel anoher high capacitance (at least 10uF) electrolytic capaciotr ( 6.3V or higher) also in order to provide the energy for prompt consumption from the load
Is it a step up or a step down a transformer has 20 primary windings and 100 secondary windings the secondary voltage is 25v?
If a transformer has 20 primary windings and 100 secondary windings, it is a step up transformer. If the secondary voltage is 25v, the primary voltage will be 5v, because the turns ratio is 20 to 100, or 1 to 5.
How 70V 25V 8-ohm and 4-ohm speaker loads works?
In a 70V distributed audio system, amplifiers output audio signals at a higher voltage (70V) to allow for longer cable runs with reduced signal loss and the ability to connect multiple speakers in parallel. The 25V system operates similarly but is used for shorter distances and fewer speakers. Speakers rated at 8-ohms or 4-ohms can be connected to the system using transformers that match their impedance to the 70V or 25V lines, ensuring efficient power transfer and sound quality. In both cases, the transformer allows for multiple speaker loads to be connected without overloading the amplifier.
Why rs232 voltage level converting to ttl level?
RS-232 is a standard built a longer while ago, and its specifications dictate a maximum voltage of +-25V. HIGH signal levels at +-5V, +-12V and +-15V are not uncommon. The range of operation is from -25V to +25V. Also, RS-232 standard notes that levels between -3V and +3V are illegal (as in, they are assumed not to exist, nor carry any information). On the other hand, TTL stands for Transistor-Transistor Logic, and the maximum rating for that is 5V. HIGH signal levels are at any point above 3.5V. The range of operation is between 0V and 5V. If one were to connect these with no conversion, the TTL device would probably be burned. Even if it would withstand, the designs are sufficiently different for them not to communicate properly. Thus, the need to 'bridge the gap' between the two.
