0
Yes, you can use 6-ohm and 8-ohm speakers on the same channel of a tuner, but it's important to consider the total impedance load the tuner can handle. When connected in parallel, the total impedance will drop, which may strain the tuner if it exceeds its rating. If connected in series, the total impedance will increase, which may reduce power output. Always check your tuner's specifications to ensure safe operation.
What else can I help you with?
Will wiring a 16 ohm woofer with a 16 ohm tweeter in parallel result in a total ohm load of 8 ohms?
If you mean as pairs, yes. put an 8 Ohm and a 16 Ohm speaker in parallel for each channel. The 16 Ohm speakers will take 1/3 the power and the 8 Ohm speakers will take 2/3 the power. The resulting impedance will be 5.33 Ohms.
Can you run 4ohm resistor to make 4 ohms speakers 2 ohm?
Yes, you can safely use a 4 ohm amp with one 8 ohm speaker, but you will not achieve full power. The 4 ohm amp is designed to supply a certain voltage into a 4 ohm speaker. Supplying that same voltage to an 8 ohm speaker will result in half the power, or -3dB. For maximum power, use a 4 ohm speaker, or two 8 ohm speakers in parallel.
Can you run 4 70w speakers on a 150w amp or will it blow?
It's entirely possible to use four 70W speakers with a 150W amplifier but the method will depend on the speakers and the amplifier specification. We will assume that the amplifier will deliver up to 150W per channel, so two speakers will be used on each channel. If the amplifier is rated to drive a 4 ohm load, then two 8 ohm speakers can be wired in parallel and connected. In this instance, take care NOT to drive the amplifier too hard. It will overdrive the speakers at about the same time that it will begin to show a distorted output. This is a condition that can easily damage speakers so be very conservative with the volume control. If the speakers are 4 ohm speakers, they can be wired in series to provide a total impedance of 8 ohms. If the amplifier is rated to deliver 150W into 4 ohms, then the total power to the speakers will be lower than to a single speaker. The benefit is that no speaker can be over-driven and there is a good amount of headroom for safety.
Are Baby Advent II speakers 8 ohm?
They are 6 ohm.
What is better 16 ohms speakers or 8 ohms speakers?
It depends on the application. If you have an amp that is stable in 8 ohms per channel, then 8 ohm speakers will work best. However, if you wanted multiple speakers on that channel you could use two 16 ohm speakers.
I have a 2 channel nitro amp 2000watts amp and it always gets hot after 10min. it's been hooked it up to several cars and it's the only amp that gives trouble every other amp works fine?
If it's running so hot you can't touch it, in most cases it will be due to either the way the speakers are hooked up or the impedence of the speakers. You can incresse the resistance to the amp to have it run cooler by connecting speakers in series or getting speakers with a higher ohm rating. The lower the resistance (2 ohm, 4 ohm, 8 ohm) the more current flows though the amp making it hotter. Remember if you hook multiple speakers in parallel it will cut the resistance in half. So if you connect speakers that are 4 ohm to the same channel you are running at 2 ohm. Check your amp's ratings.
Will wiring a 16 ohm woofer with a 16 ohm tweeter in parallel result in a total ohm load of 8 ohms?
If you mean as pairs, yes. put an 8 Ohm and a 16 Ohm speaker in parallel for each channel. The 16 Ohm speakers will take 1/3 the power and the 8 Ohm speakers will take 2/3 the power. The resulting impedance will be 5.33 Ohms.
Can I connect two 2 ohm speakers to the front channels of my amp and then connect 2 4 ohm speakers to the rear channels of my 4 channel amp?
This depends on your amplifier's specifications. i would recommend looking in the amplifier's service manual to avoid disapointment or damage to your amplifier or speakers.
How to Replace door speakers 300m?
The front door speakers are very easy to replace... The Grill covering the speakers just pops out: Open the door. pull out on the grill from the hinge side of door toward the latch side of the door. Then remove three torque screws. and disconnect the wiring harness. The front door speakers are 2-ohm, bass-channel. Most off-the-shelf speakers are either 4-ohm or 8-ohm multi-way speakers.
How do you wire two 8 ohm speakers and keep a 8 ohm load?
in parallel No. Two 8 ohm 'speakers in parallel present a 4 ohm load.
Will 6 ohm speakers sound quality be affected with using an 8 ohm sound system?
The 6 ohm speakers will sound fine with the 8 ohm amplifier.
What is the ohm rating of rear speakers in a Pontiac sunfire?
The ohm rating is 8 ohm on the rear speakers in a Pontiac Sunfire. They can be switched out, as long as the front and rear speakers match.?æ
Can you run 4ohm resistor to make 4 ohms speakers 2 ohm?
Yes, you can safely use a 4 ohm amp with one 8 ohm speaker, but you will not achieve full power. The 4 ohm amp is designed to supply a certain voltage into a 4 ohm speaker. Supplying that same voltage to an 8 ohm speaker will result in half the power, or -3dB. For maximum power, use a 4 ohm speaker, or two 8 ohm speakers in parallel.
Can you run 4 70w speakers on a 150w amp or will it blow?
It's entirely possible to use four 70W speakers with a 150W amplifier but the method will depend on the speakers and the amplifier specification. We will assume that the amplifier will deliver up to 150W per channel, so two speakers will be used on each channel. If the amplifier is rated to drive a 4 ohm load, then two 8 ohm speakers can be wired in parallel and connected. In this instance, take care NOT to drive the amplifier too hard. It will overdrive the speakers at about the same time that it will begin to show a distorted output. This is a condition that can easily damage speakers so be very conservative with the volume control. If the speakers are 4 ohm speakers, they can be wired in series to provide a total impedance of 8 ohms. If the amplifier is rated to deliver 150W into 4 ohms, then the total power to the speakers will be lower than to a single speaker. The benefit is that no speaker can be over-driven and there is a good amount of headroom for safety.
Can you hook up two 8 ohm svc subwoofers to a one channel amp?
If you connect two 8 ohm speakers to the average car amp, then yes, probably. Most car amps can handle a 4 ohm load, which is what it would be.
Whats the speaker sizes in a 2005 impala?
The front speakers should be 6.5" and the rear should be 6x9". You will want to make sure you have the correct ohm speakers though. My 2004 impala has 2ohm speakers and my friends has 4ohm speakers. You can put 4 ohm speakers in a 2 ohm system but your sound quality will suffer greatly. Do not put 2 ohm speakers in a 4 ohm system though, that will cause bigger problems.
What ohm should the speaker be if i want to achieve a 2 ohm load from 4 speakers?
Four 8 ohm speakers wired in parallel would give an effective 2 ohm load.
