Yes, you can use unsanded grout for floor tile but you'd only want to use it if the grout lines were 1/8" wide or less - like for granite or marble tiles.
If using those, be sure you have a pefectly flat surface.
ANSWER:
You never want to use sanded grout with marble. If the marble has to be restored or re-polished for any reason the sand in the grout with act like sandpaper on the stone.
You can. It is less gritty but it works. Edit - While this is true, it's important to understand the wall grout is designed for thinner grout lines, so if you use it on the floor, make sure your grout lines are thin. Otherwise, the grout will crack.
Yes, you can change the color of the grout. There are products that you can use to try to die the grout or you can just have your tile re-grouted.
Not JUST a grout no. You can get a cement that will also work as a grout but a pure grout would not have the adhesion required to stick the tiles to the wall properly, you should not use it as a cement.
Yes.... But if the tile is glazed and/or the grout is epoxy (unlikely unless in a commercial building) these do NOT need to be sealed (neither will absorb water so they won't accept the sealer). The rule of thumb is to put a few drops of water on the tile and the grout, if it soaks in within 30 seconds it needs to be sealed. Never use a topical sealer. Always use a waterbased PENETRATING sealer. You will need to reapply bi-yearly or yearly in most situations, more if the tile is exposed to water. Hope this helps..........
Duraceramic tile will not chip, break or crack like regular ceramic tiles. Manufactured in a 16" square format with scoring, you can cut the score lines to make 4 tiles 8" square. They are best installed in dry residential rooms. This leaves the bathroom out. Use the proper underlayment for the type of floor you are installing Duraceramic tile on. Spread Congoleum Duraceramic tile adhesive on the underlayment using a tile trowel. Allow to dry until tacky, then set the tiles with spacers. Use a roller to press tiles into place, and allow to dry 24 hours. Grout with Congoleum Duraceramic grout.
Most often, sanded grout is used for floor tiles because the grout lines are usually greater than 1/8" wide. Sanded grout is necessary for the wider lines to give added strength, and to keep your grout from cracking and chipping out. Unsanded grout must be used if your grout lines are narrower than 1/8", because the grains of sand in sanded grout could cause air pockets and prevent good adhesion to your tiles - and it will crack and chip out as well. Sanded and unsanded grouts are cement-based. One alternative grout on the market is epoxy-based. It is neither sanded nor unsanded, but will work fine in either narrow or wider grout lines. If your grout lines are wider than 1/2", or if you are using saltillo tiles, you must use saltillo grout. Other grouts will not handle this wider width.
Sadly, if you are looking to fix the tile with the grout, there is none. If you are looking for something that will not crack because of movement, a high end epoxy grout.
You should use the grout that will work best for the biggest grout space that you need. So for a grout width like you described, 1/16 to 1/2, you should use sanded grout. Unsanded grout will look terrible in a 1/2" grout joint, but sanded grout will look great in both. Use sanded.
You can. It is less gritty but it works. Edit - While this is true, it's important to understand the wall grout is designed for thinner grout lines, so if you use it on the floor, make sure your grout lines are thin. Otherwise, the grout will crack.
To effectively remove floor tile grout, you can use a grout saw or a rotary tool with a grout removal attachment to carefully scrape away the old grout. Be sure to wear safety goggles and a dust mask to protect yourself from debris. After removing the grout, clean the area thoroughly with a damp cloth to remove any remaining residue.
To properly grout bath tile for a professional and long-lasting finish, follow these steps: Choose the right type of grout for your tiles (sanded or unsanded). Mix the grout according to the manufacturer's instructions. Apply the grout with a rubber float, pressing it into the joints at a 45-degree angle. Use a grout float to remove excess grout from the surface of the tiles. Allow the grout to set for the recommended time before wiping off excess grout with a damp sponge. Seal the grout to protect it from moisture and stains. By following these steps, you can ensure a professional and long-lasting finish for your bath tile grouting.
Tile has a glass finish & doesnt need wax, Wax can cause a slip & fall hazard when it gets wet Sealing tile is a misnomer, you really only need to seal the GROUT.. stop by the Depot & get some grout sealer, better for the grout
To remove a tile floor, start by removing the grout between the tiles using a grout saw. Then, use a chisel and hammer to carefully pry up the tiles. Be sure to wear protective gear and work slowly to avoid damaging the subfloor.
To efficiently remove bathroom tile floor, start by removing the grout with a grout saw or chisel. Then, use a hammer and chisel to break up the tiles and pry them up. Be sure to wear safety goggles and gloves for protection.
To properly grout a tile floor for a professional and durable finish, follow these steps: Mix the grout according to the manufacturer's instructions. Apply the grout with a rubber float at a 45-degree angle, pressing it into the spaces between the tiles. Use a grout float to remove excess grout from the surface of the tiles. Allow the grout to set for the recommended time before wiping off excess grout with a damp sponge. Seal the grout to protect it from stains and moisture.
Non Sanded grout can be used in any size grout joint but is ideal in smaller joints usually up to 1/4" The main draw back to using unsanded grout in larger joints is that it may crack over time. If you are unwilling to remove all the grout and use a sanded grout, it is best to make sure the grout is cured and sealed properly to limit and minimize cracking.
To properly grout floor tile for a professional and durable finish, follow these steps: Mix the grout according to the manufacturer's instructions. Apply the grout with a rubber float, pressing it into the spaces between the tiles at a 45-degree angle. Use a grout float to remove excess grout from the surface of the tiles. Allow the grout to set for about 15-30 minutes, then wipe off excess grout with a damp sponge. Let the grout dry for 24 hours before sealing it with a grout sealer for added durability.