answersLogoWhite

0

What else can I help you with?

Continue Learning about Engineering

How do you make a control panel to change the rotation of three phase induction motor?

The control panel will be based around a set of reversing magnetics. Depending on how you want to control the mags will depend on what type of peripheral equipment you will need to add to the control panel.


How do you wire a 3 phase 4 wire plug does it matter which leg the wild is on?

Of the three conductors the combination is irrelevant except with respect to phasing and rotation. If the equipment requires proper phasing ( motors need to turn a specific direction), wire it up and "bump" a contactor. If the direction of rotation is not correct, swap 2 of the conductors. Do the swap at the lineside of the disconnect/ breaker, etc. In the case of an HVAC/R non-scroll compressor, rotation is not an issue. One exception would be if the control system were to use one phase to neutral. This should not be the case as you specified 4 wire three phase, which implies the fourth conductor by code, is a ground and control is provided by two of the three conductors providing control voltage. Check the schematic and/ or contact the manufacturer of the equip. lc


When a control is required to control space or product temperature is called a what?

thermostat


What is a tachogenerator in control system?

a device to measure rotation speed of a shaft as a proportional voltage


What does the control module do on an electric scooter?

Controls the application of voltage to the motor to control speed and direction of the motor. If there is a built in charger it would also control the charging process.

Related Questions

Do bicycle gears change the direction of motion?

No, bicycle gears do not change the direction of motion. They adjust the ratio of pedal rotation to rear wheel rotation, allowing the rider to maintain an optimal cadence and control the speed and effort required while riding.


What is RCS direction?

RCS direction refers to the orientation in which a Reaction Control System (RCS) is used to maneuver a spacecraft. The RCS can provide thrust in various directions to control the attitude and position of the spacecraft in space. The direction of RCS thrust can be adjusted to achieve specific maneuvers such as rotation, translation, or stabilization.


How do you make a control panel to change the rotation of three phase induction motor?

The control panel will be based around a set of reversing magnetics. Depending on how you want to control the mags will depend on what type of peripheral equipment you will need to add to the control panel.


What are three factors that control the path that a surface current?

The three factors that control the path of a surface current are wind direction, the Earth's rotation (Coriolis effect), and the shape of the coastline or the presence of land masses. These factors influence the direction and strength of surface currents in the ocean.


How do you wire a 3 phase 4 wire plug does it matter which leg the wild is on?

Of the three conductors the combination is irrelevant except with respect to phasing and rotation. If the equipment requires proper phasing ( motors need to turn a specific direction), wire it up and "bump" a contactor. If the direction of rotation is not correct, swap 2 of the conductors. Do the swap at the lineside of the disconnect/ breaker, etc. In the case of an HVAC/R non-scroll compressor, rotation is not an issue. One exception would be if the control system were to use one phase to neutral. This should not be the case as you specified 4 wire three phase, which implies the fourth conductor by code, is a ground and control is provided by two of the three conductors providing control voltage. Check the schematic and/ or contact the manufacturer of the equip. lc


What is mean by commutation switch?

A commutation switch is a device used to reverse the direction of current flow in a circuit, typically in motor control applications to control the direction of rotation. It allows for the smooth transition of current between different circuit elements, such as switching from one winding to another in a motor to maintain torque.


What kinds of control equipment are there?

There are various types of "control", therefore, there are various types of control equipment. There is birth control equipment, livestock control equipment, air pollution control equipment, etc.


What are the six steps required by OSHA for isolating a confined space?

1. Prepare for shutdown. 2. Shut down the equipment 3. Isolate the equipment 4. Apply lockout/tagout 5. Control stored energy 6. Verify equipment dectivation


Can you control sound wave direction by changing the direction and presure of air?

You can control sound wave direction, by changing the direction and pressure of air.


What is MS ring complex?

A protein complex found within the cytoplasmic membrane of flagella-containing bacteria. It contains switch proteins, which control the direction of rotation, and motor proteins, which are driven by a proton gradient. The MS ring complex brings about the rotation of the flagella to generate thrust.


Why is there a time delay in an oil safety control?

Generally oil safety switches sense the oil pressure. If there is no preset pressure then the oil safety switch acts (to switch off or cut off the device) For an equipment that needs to be protected against the low oil pressure, such switches are used. when the equipment is standstill (or not running) then the oil pressure is also zero. When the equipment starts running, during the initial few seconds the oil pressure builds up from zero to required pressure. The timer is required not to cut off the equipment control in this initial few seconds. Control system waits for few seconds allowing the pressure to build up and after the preset time, if the pressure does not build up then it switches off the equipment since running the equipment with oil pressure is not good for the equipment.


Why is there a delay in an oil safety control?

Generally oil safety switches sense the oil pressure. If there is no preset pressure then the oil safety switch acts (to switch off or cut off the device) For an equipment that needs to be protected against the low oil pressure, such switches are used. when the equipment is standstill (or not running) then the oil pressure is also zero. When the equipment starts running, during the initial few seconds the oil pressure builds up from zero to required pressure. The timer is required not to cut off the equipment control in this initial few seconds. Control system waits for few seconds allowing the pressure to build up and after the preset time, if the pressure does not build up then it switches off the equipment since running the equipment with oil pressure is not good for the equipment.