answersLogoWhite

0

more brittle

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Engineering

Is high carbon steel stronger than tempered steel?

Tempered steel is not a classification of steel. It is a term used to indicate that the steel has undergone proper heat treatment in which case..yes, the steel that has been properly hardened and tempered would be stronger. This answer assumes that the high carbon steel is in its annealed state and has not received heat treatment and tempering of its own.


Why carbon is better then any other for steel?

It is required to make steel the more carbon the steel contains the harder and stronger it will get, if you have to much carbon the steel will be brittle and crack easy. carbon is a good element to bond with becuase it has four bonds


Why is is high carbon steel is limited to cutting tools?

Higher contents of carbon make the steel harder but more brittle. The harder steel will cut better and hold an edge longer but has much less shear strength.


What is the difference of singly reinforced beam from doubly reinforced beam?

Singly reinforced beams have reinforcing only on the tension face. Doubly reinforced beams have reinforcing on the tension and compression face. Doubly reinforced beams can increase section capacity, but are primarily used to increase the ductility of the concrete beam. In certain codes, if the concrete section is controlled by the concrete failing in compression before the tension steel rebar yields (called a compression-controlled or brittle section), the calculated section capacity must be reduced to account for the brittle and sudden/unpredictable nature of a compression controlled (also called a brittle) failure. In order to make the section controlled by the yielding of the tension reinforcement (called a tension-controlled or ductile section), the ductility must be increased. This can be accomplished by adding steel in the compression zone, which gives strength to the compression area, thereby delaying the failure of the concrete. Enough compression steel can cause the section to switch from a brittle mode-of-failure to a ductile mode-of-failure, thereby permitting the designer to not decrease the section capacity from its calculated value. When identifying a doubly- reinforced beam, be sure that the steel in the compression area is meant to be for strength. Oftentimes, all faces of a beam will have some reinforcing for temperature/shrinkage protection and to tie the stirrups to. Steel that is only there for temp/shrinkage or to facilitate tying the rebar will usually be small and not much of it. In buildings, they will be often #3 bars @ 12" centers. In bridges, they may be #4 bars. These small bars should not be counted as compression-zone reinforcing. Look for bars in the compression zone that are of similar size to the main tension reinforcing.


Are steel bars made in circles?

Steel companies make steel bars in circles

Related Questions

What is non-ductile?

Materials like gold and copper can be bent; they are malleable or ductile. Materials that are brittle and break easily are non-ductile. Conventional concrete is non-ductile (and breaks under stress of earthquakes)(or other tensile challenge). Metal (steel) mesh or synthetic fibers are added to concrete to make it more ductile.


What do they add to steel to make it ductile?

To make steel ductile, elements like nickel, chromium, and manganese are added during the manufacturing process. These elements help improve the steel's flexibility and ability to deform without fracturing.


What is non ductility?

Materials like gold and copper can be bent; they are malleable or ductile. Materials that are brittle and break easily are non-ductile. Conventional concrete is non-ductile (and breaks under stress of earthquakes)(or other tensile challenge). Metal (steel) mesh or synthetic fibers are added to concrete to make it more ductile.


Is high carbon steel stronger than tempered steel?

Tempered steel is not a classification of steel. It is a term used to indicate that the steel has undergone proper heat treatment in which case..yes, the steel that has been properly hardened and tempered would be stronger. This answer assumes that the high carbon steel is in its annealed state and has not received heat treatment and tempering of its own.


Why quenching steel must be tempered?

Quenching steel involves rapidly cooling it to increase hardness, but this can make it too brittle. Tempering is a process where the hardened steel is heated to a specific temperature and then cooled slowly. This helps relieve internal stresses and makes the steel tougher and more ductile, balancing hardness with flexibility.


Why is mild steel used to make chains?

Because hard steel would be brittle and break.


Why does hardened steel rust faster?

Hardened steel can rust faster than regular steel because the hardening process can disrupt the steel's natural corrosion resistance. This can lead to increased vulnerability to rust and other forms of deterioration. Hardened steel may also have more exposed surface area due to the hardening process, which can make it more prone to rusting.


How does pearlite affect mechanical properties?

Pearlite enhances the strength and hardness of steel due to its fine lamellar structure. It can also improve wear resistance and toughness. However, an excess of pearlite can make the material too brittle, affecting its overall toughness.


What is toughening process in steel?

Toughening is a process in steel in which the material is reheated to a specific temperature, then cooled slowly in order to increase its ductility and reduce its hardness. This helps to make the steel less brittle and more resistant to fractures or cracks under stress.


What is the ductility of ruthenium?

Ruthenium is a brittle metal with low ductility, meaning it does not easily deform under tensile stress. Its properties make it more suitable for certain applications like catalysis and electronics where its strength and corrosion resistance are beneficial.


What conditions make rock more ductile?

High temperature and pressure conditions typically make rocks more ductile. The presence of water and certain minerals can also contribute to increased ductility in rocks by facilitating deformation and reducing the likelihood of brittle failure. Additionally, the composition and structure of the rock itself can influence its ductility.


Can liquid nitrogen be used to cut steel?

Yes, liquid nitrogen can be used to cut steel. When liquid nitrogen is applied to steel, it causes the steel to become extremely brittle and easier to break or cut. This method is often used in industrial applications for precision cutting of steel components.