0
What else can I help you with?
What is the value of amperes for 100 volts at constant resistance?
V = I*R, so take 100 volts and divide it by the value of the resistance to get the current. Current is measured in amperes.
State 3 functions of wheatstone bridge?
Wheatstone bridge is used to calculate the resistance of unknown resistor in the circuit.
How to measure the root mean square value of MESURED voltAGE in convential voltmeter?
A conventional voltmeter displays 0.707 of the peak voltage when it measures AC.In doing so, it displays the RMS value of the measured voltage IF the measured voltage is a sinusoid.If the measured voltage is not a sinusoid, then its peak value is 1.414 times the displayed number, andyou have to calculate the RMS based on the waveform.
Is 2 million ohms higher resistance?
Yes, 2 million ohms represents a very high resistance. In electrical terms, resistance is measured in ohms, and a value of 2 million ohms (or 2 megohms) indicates that the material or component resists the flow of electric current significantly. This level of resistance is common in certain applications, such as in insulation or high-resistance circuits.
What happens to the total resistance of a series circuit when another resistor is added?
Simply put, the purpose of a resistor is to 'resist' the flow of current. Ohm's Law tells us that for a given voltage, the larger the resistance, or value of that resistor, the lower the current that will flow. Ohm's Law states that I (current) = E (voltage) / R (resistance) - where current is measured in amps, voltage is measured in volts and resistance is measured in ohms.
How do we calculate the cold resistance of the bulb?
The cold resistance of a bulb can be approximated by measuring the resistance of the filament with a multimeter when the bulb is turned off and at room temperature. The resistance measured in this state can give an estimation of the cold resistance of the bulb. Keep in mind that this value may not be exact due to factors like the temperature coefficient of resistance and the non-linear behavior of the filament's resistance.
Is resistor measured in amps?
No, resistors are measured in ohms, not amps. Ohms represent the resistance offered by the resistor to the flow of current, whereas amps (amperes) represent the measure of current flowing through a circuit.
How do you calculate percentage error for density of pennies?
Percent error refers to the percentage difference between a measured value and an accepted value. To calculate the percentage error for density of pennies, the formula is given as: percent error = [(measured value - accepted value) / accepted value] x 100.
What is the value of amperes for 100 volts at constant resistance?
V = I*R, so take 100 volts and divide it by the value of the resistance to get the current. Current is measured in amperes.
How do i find the current after it passes through a resistor?
Current can be measured with an ammeter. If you want to calculate it from other values, you will quite often use Ohm's Law (just divide voltage by resistance, if you know the resistance value of the resistor) - or perhaps a combination of Ohm's Law and Kirchoff's Laws.
How do you calculate the percentage error in a measurement or calculation?
To calculate the percentage error in a measurement or calculation, you first find the difference between the measured or calculated value and the accepted or true value. Then, divide this difference by the accepted value and multiply by 100 to get the percentage error. The formula is: Percentage Error (Measured Value - Accepted Value / Accepted Value) x 100
How can you calculate the difference between measured and calculated value?
A simple subtraction. Take the smaller from the larger
State 3 functions of wheatstone bridge?
Wheatstone bridge is used to calculate the resistance of unknown resistor in the circuit.
Why resistor should disconnected from the circuit when measured the value of resistor?
if not disconnected you will measure the resistance of the circuit in parallel with the resistor.
What the function of tolerance for resistor colour code?
Tolerance indicates how much the measured value of a resistance is different from its theoretical value, and it is calculated using percentages.
What is the percentage error in p?
Percentage error in p is calculated by taking the absolute difference between the measured value and the true value, dividing by the true value, and then multiplying by 100 to get the percentage. The formula is |(measured value - true value) / true value| * 100.
A resistor Connected to a 9 Volt supply dissipates 3 watts calculate the value of the resistance?
about 27ohms
