0
What else can I help you with?
What is the similarities of plastering sand and concreting sand?
Plastering sand is find sand screened to suit the plaster coarse i.e. base coat or finish coat. For finish coat very fine sand is used. Sand for concrete is not sived if pebles are not present. Both sand shall be sweet sand, if from sea it has to be washed before use.
Can you use silica sand as a dry screed over underfloor heating pipes?
Unfortunately not. You require a 0-4mm sharp sand which can be purchased through most builders merchants. The mix should be approximately 1:4 Cement / Sand ratio. Mix to an earthy consistency and compact well. The cement is the conductor of the heat. Good luck with the project.
What is best for cement mortar fine sand or coarse sand?
Fine sand is best for mortar.
Is sand mixed with mortar mix for laying concrete blocks?
Not just any sand. Mortar sand. Mortar sand is a larger grain sand that has been washed and screened to remove any rocks or pebbles.
How does shear strength of fine sand effect by void ratio?
Shear strength of fine sand is determined by the angularity of the sand particles, the grading of the sand. These two features governs the critical state shear strength parameters of the sand. Density, however, dictates the peak shear strength of the sand. i.e. the denser the sand, the higher the peak shear strength. But the critical shear strength remain the same. The denser the sand, the lower the void ratio. Shear strength of fine sand is determined by the angularity of the sand particles, the grading of the sand. These two features governs the critical state shear strength parameters of the sand. Density, however, dictates the peak shear strength of the sand. i.e. the denser the sand, the higher the peak shear strength. But the critical shear strength remain the same. The denser the sand, the lower the void ratio.
How do you calculate airflow through sand trap louvers?
determine how much air can safely be run through the louver by multiplying the louver free area by the design velocity ( 7.2 sq ft x 893 fpm). The resulting Volume of Air for Louver 1 is 6424 cfm.
What is the minimum stream velocity needed to carry a particle of sand?
The minimum stream velocity needed to carry a particle of sand depends on the size and weight of the sand particle, as well as the characteristics of the stream such as flow rate and turbulence. In general, for typical sand particles, a stream velocity of around 0.3 m/s to 1 m/s is needed to entrain and transport them.
A stream is carrying sand Which two factors determine when the sand will settle out of the stream?
The settling rate of the sand particles and the flow velocity of the stream are the two main factors that determine when the sand will settle out of the stream. Higher settling rates and lower flow velocities typically lead to quicker settling of the sand particles.
What will happen to the velocity of the car as sand is loaded onto it?
The velocity of the car will decrease as sand is loaded onto it due to the increase in mass. This increase in mass requires more force to accelerate the car to maintain the same velocity. Additionally, the added weight may affect the car's ability to overcome friction and air resistance, further reducing its velocity.
Which sediment is the largest that could be carried by a stream flowing at a velocity of 100cmsec?
sand
What wind carrying sand grains deposits the sand when the wind?
The wind carrying sand grains deposits the sand when the wind's velocity decreases, or when an obstacle interrupts the wind flow. This causes the heavier sand grains to settle and accumulate, forming sand dunes.
What is the definition of the word sandblasting?
Sandblasting is a method of cleaning where sand is sprayed at something at high velocity. The abrasive action of the sand cleans the object.
What does buffet mean?
Buffet means like all you can eat. Buffet can also mean to hit. For instance, if you were walking through a sandstorm, sand would be flying at your face and would hit you. Thus, you would be buffeted by the sand. == ==
Why are sand dunes important?
Sand or fine particles, when blown by the wind, will form ridges, called sand dunes. The wind on their upwind face is subject to a slightly higher wind velocity - caused by the dune's obstruction itself. This upwind slope will have a rounded shape. Beyond the crest, the sand will drop out thus creating a hollow curved shape.
Is the threshold velocity for silt higher than the threshold velocity for sand?
No, the threshold velocity for silt is typically lower than the threshold velocity for sand. Silt particles are smaller and lighter than sand particles, so they require less energy to be moved by water or wind.
How do you hit out of a sand trap in golf?
Follow Through. Do NOT hit the ball first. Use the sand behind the ball to help push the ball out of the bunker. Open your sand wedge face so it's facing the sky. Place the ball forward in your stance, then hit behind the ball an inch or two. Remember to aim left of your target to compensate for the open club face.
How do you separate the gravel and the sand?
Sand and gravel can be separated by sifting them through a mesh, that will allow the sand to fall through, but will hold back the gravel.
