0
What else can I help you with?
How do you calculate fuse size in a 150hp 3 phase 600V motor?
find the line current first... i=(150*735.5) / (sqrt(3)*600*0.8) assume pf of 0.8 the current value gines u reqd fuse rating
What is the difference between 3amp and 13amp fuse?
If the fuse thsat has blown is a 3 amp, you should only replace it with a 3 amp fuse, which is good for appliances up to 700 watts (In the UK, on 240 volts). Do not replace a 3 amp fuse with a 13 amp fuse, it gives much less protection. If you replace a 13 amp fuse with a 3 amp fuse, the 3 amp will likely blow, since the 13 amp fuse should be protecting a powerful appliance such as a heater, between 2000 watts and 3000 watts.
What is the correct fuse rating to provide short-circit protection for a 100HP 200V 3-0 wound-rotor motor?
what is the correct fuse rating to provide short-circit protection for a100 HP 200V 3-0 wound-rotor motor
Fuse size for 7.5 HP 3 Phase 440 Volt Motor?
The electrical code states that a 7.5 HP 460 volt three phase motor draws 11 amps. For fuse sizes, non time delay - 30 amps, time delay type D - 20 amps and if using a breaker it will be 30 amps. Minimum wire size is #12 and the maximum setting of overload devices will be 13.75 amps
What are 3 reasons why there are not 24 volts at the thermostat when heat or air is called for?
F.A.U turned off Bad transformer Blown low voltage fuse
Where is the fuse box in the Mazda 3?
The fuse panel in my 2006 Mazda 3 is under the hood next to the battery on the driver side. The fuse box is under the passenger side glove box on some models.
Where is the fuse location for the cigarette lighter in a 2004 Mazda 3?
in your anus
Where is the fuse box located for 2005 Mazda 3?
All Mazda 3 haves Fuse Box in left side of underhood spase and second box is hidden inside the car, below the foots of passenger.
Is the fuse box for a 5 speed 2.3 liter Mazda 3 sport the same as the automatic 2.3 liter Mazda 3 sport?
yeah it is
Where is the fuse for hooter of Mazda 3?
The fuse for the horn (hooter) of a Mazda 3 is typically located in the fuse box under the dashboard on the driver's side or in the engine compartment. You can find the specific fuse for the horn by consulting the owner's manual, which provides a fuse diagram indicating the exact location and amperage of the horn fuse. If you suspect a blown fuse, check this location and replace it if necessary.
Where is lighter fuse Mazda 3?
In a Mazda 3, the lighter fuse is typically located in the fuse box. For most models, the fuse box can be found under the dashboard on the driver's side or in the engine compartment. To identify the specific fuse for the lighter, refer to the fuse diagram usually found on the inside cover of the fuse box or in the owner's manual. If the lighter is not working, check this fuse for any signs of damage or a blown fuse.
Which fuse is for windshield wipers in a 2008 Mazda 3?
Fuse number 53 (rear wiper) and 68 (front wipers)
Where is fuse to disconnect ABs for 2007 Mazda 3?
In a 2007 Mazda 3, the fuse for the anti-lock brake system (ABS) is located in the fuse box under the dashboard on the driver's side. To access it, remove the cover of the fuse box and look for the fuse labeled for the ABS. If you need to disconnect the ABS, you can remove this fuse. Always refer to the owner's manual for specific fuse locations and ratings.
Where is fuse for clock 2006 Mazda 3?
The fuse for the clock in a 2006 Mazda 3 is located in the interior fuse box, which is typically found under the dashboard on the driver's side. Look for a fuse labeled "CLOCK" or check the owner's manual for the specific fuse number. If the clock is not functioning, it may be due to a blown fuse, so inspecting and replacing it could resolve the issue.
What type of ATF is in a 2005 Mazda 3?
atf for 05 Mazda 3 is any m-v
Where is the fuse box located in a 2008 Mazda 3?
under the dash passenger side
Where is the fuse for the blower fan on a 2005 Mazda 3?
In a 2005 Mazda 3, the fuse for the blower fan is located in the fuse box under the dashboard on the driver's side. You'll need to remove the cover to access the fuses. Look for the fuse labeled "Blower" or "HVAC" in the diagram on the cover for identification. If the fuse is blown, replacing it should restore functionality to the blower fan.
