0
What else can I help you with?
Why should large concrete slabs be laid with expansion so that they are not touching?
because large slabs of concrete have expansion joints between them.
What is two way slab?
Two-way slabs are rectangular reinforced-concrete slabs that are supported on all sides. The reinforcement is placed perpendicular to the sides.
What is the minimum spacing of construction joints in slabs?
18
What should be the required steel in column beam and slab?
The required steel in columns, beams, and slabs is determined by structural design calculations that consider factors like load-bearing capacity, span length, and building codes. Typically, columns require higher steel reinforcement due to axial loads, while beams need to resist bending moments. Slabs generally have a lower steel requirement and are reinforced for tensile strength. The specific amount and type of reinforcement, such as rebar sizes and spacing, should be based on detailed engineering analysis and design standards.
Can you lay new paving slabs on top of old ones?
You could, but then you might risk causing damage to the new paving slabs, or exacerbating drainage issues. I would go ahead and remove the old slabs as these are usually just laid in with plain sand between them. Even if it's cement, I'd hate to have to do it over.
How many patio slabs to cover a area of 9 meters to 2 square meters?
The answer will depend on the size of the patio slabs.
How many 400mmx400mm slabs will you need to cover 6ftx4ft?
14
How many 600mmx600mm slabs do i req to cover an area of 450sq'?
20 I believe
How many 450x450 slabs would i need to cover 30ftx30ft space?
400 at least
How many paving slabs 600mm by 600mm to cover 20 square meters?
To find out how many 600mm by 600mm paving slabs are needed to cover 20 square meters, first convert the dimensions of the slab to meters: 600mm is 0.6 meters. The area of one slab is 0.6m x 0.6m = 0.36 square meters. To cover 20 square meters, you would need 20 / 0.36 ≈ 56 slabs.
How many slabs would you need for a sq meter if flags are 600mm x 600mm?
To determine how many slabs are needed for one square meter, first convert the dimensions of the slabs from millimeters to meters. A 600mm x 600mm slab is 0.6m x 0.6m, which has an area of 0.36 square meters. Therefore, to cover one square meter, you would need approximately 2.78 slabs. Since you can't have a fraction of a slab, you would need 3 slabs to cover one square meter.
How many 600mm x 300mm slabs do you need to cover 55 sq meters?
305.56
How many square meters does 112 18x18 inch slabs cover?
23.41 sq m
How many 18inch x 18inch slabs to cover 15ft x 7ft area?
140
How many 450mm x 450mm slabs will cover the space of 20ft x 20ft?
20 ft= 6096 mm (6096 * 6096) / (450 * 450) = 183.512178 184 slabs
How many patio slabs 44 cm by 44 cm would be need for area 10 feet by 13 feet?
You will need 63 44cm x 44cm slabs to cover that area.
How many paving slabs would you need for a square meter of flags are 450mm x 450mm?
To determine how many 450mm x 450mm paving slabs are needed for a square meter, first convert the dimensions of the slabs to meters: 0.45m x 0.45m. The area of one slab is 0.45m x 0.45m = 0.2025 square meters. Therefore, to cover one square meter, you would need approximately 1 / 0.2025 ≈ 4.94 slabs. Since you can't have a fraction of a slab, you would need 5 slabs to cover a square meter.
