0
What else can I help you with?
How do I turn-on water supply to hot water boiler it is heating but nothing goes to the radiators?
Check your gauge to make sure you have enough pressure and your flow control valve is not stuck
How shall you make the hydrostatic pressure test or the steps to follow?
procedures in testing hydrostatic pressure in fluid(water)
What would make the water pressure in a house go above 80 psi?
Area water authority could have increased water main pressure, no or defective expansion tank in house main water line if house has a backflow preventer installed, or defective /not properly set pressure reducing valve.
How do you stop the flow of an artesian well?
Put in a well head with a tap. Or make the well head very tall so that it is higher then the artesian pressure.
What does a pump develop flow or pressure?
the pump develops pressure to have the ability to make a flow of a gas or fluid take place through a vessel, pipework or valve system, as long as there is an open end to the pipe system or vessel allowing distribution of fluid to an outlet or a return pipe back to the pump body.
Does increasing pipe diameter increase water flow?
well it depends it could but for it to make a difference you will need more water pressure.
How to use a water pressure gauge effectively?
To use a water pressure gauge effectively, first attach it to a water source, such as a faucet or hose. Turn on the water and observe the gauge to see the pressure reading. Make sure to check for any leaks or fluctuations in pressure. Adjust the water flow if needed to maintain a consistent pressure reading.
How do I properly operate the shower on-off valve to control the water flow in my bathroom?
To control the water flow in your bathroom, turn the shower on-off valve clockwise to increase the water flow and counterclockwise to decrease it. Make sure to adjust the valve slowly to find the desired water pressure.
How to measure water pressure accurately and effectively?
To measure water pressure accurately and effectively, use a pressure gauge designed for water systems. Attach the gauge to a water source and ensure it is calibrated properly. Open the water source to allow water to flow through the gauge and observe the pressure reading. Make sure to take multiple readings at different times to ensure accuracy.
Underwater pressure--Can you make water flow upward continuously if you vertically submerge one end of a 1-inch pipe 10 meters or more under seawater?
Yes....that is the water will flow up the pipe until it reaches the level of the water and stop. I don't get it. At the surface level the pressure is supposed to be 14.7 psi; doubled at 10 meters deep. If submerging a pipe deep enough for a significant pressure difference, can we harness the continuous upward flow of water for some application?
How do I turn-on water supply to hot water boiler it is heating but nothing goes to the radiators?
Check your gauge to make sure you have enough pressure and your flow control valve is not stuck
How do you make water reboil without heating or removing the top?
Water boils when saturated vapor pressure of the gas molecules of water is equal to the atmospheric pressure. In order to maker water boil at these conditions, the pressure at the top of the liquid should be reduced using a vacuum pump
Can air push water out of a container?
Yes because if the container has a whole in it the air well make the water squezze out of the whole
Why are my pipes making a knocking sound?
Pipes can make a knocking sound due to water hammer, which happens when water flow is suddenly stopped or redirected, causing pressure to build up and create the noise. This can be caused by loose pipes, high water pressure, or a faulty valve.
Did pressure make current flow?
Pressure itself does not directly make current flow. Current flow is driven by the presence of an electric field, which is established by a potential difference (voltage) between two points in a circuit. Pressure could be a factor in some specific situations, such as in sensors or certain electronic components, but it is not the primary driver of current flow in a typical electrical circuit.
Why do pipes make noise when water is turned off?
Pipes make noise when water is turned off due to a phenomenon called water hammer. This occurs when the flow of water is suddenly stopped, causing a pressure wave to travel through the pipes and create vibrations that result in noise.
How much current is need for 12 VDC to flow through water?
First thing voltage does not flow current does. Voltage is the potential or pressure needed to make the current flow. Current is directly proportional to the applied voltage and inversely proportional to the resistance of the circuit. To make the current flow you have to adjust the resistance of the circuit and that would be the water in this case. Salt added to water will make the water conductive so the resistance can be adjusted thereby making the current rise or fall depending on the water solution's resistive properties. The equation that you should consider using is Amps = Volts/Resistance.
