0
What else can I help you with?
How do you calculate the resistance of a heater element that's uses 220v and draws 11amps?
The equation you are looking for is R = E/I.
Can a 240 volt single phase load connect between the high leg and regular phase leg of delta connected three phase system?
yes but voltage will be out a little.This ok for something like a heater which wont care.But for an electric motor starting and overheating maybe a problem.In the US this would be 220v single phase and 208 volts 3 phase.
What should be primary to secondary turns ratio for step downing 220V to 12V?
220V : 12V 55 : 3
How you convert 220V ac to 280v DC?
NAVEED45
How you convert the 220v AC to 220v DC?
You can make this conversion if a full wave bridge rectifier is used. Make sure that the diodes are rated for the voltage that is being used.
How is 220v water heater rewired to 110v?
To rewire a 220V water heater to 110V, you would need to change the heating element to one that is compatible with 110V. You would also need to adjust the wiring connections in the water heater to accommodate the lower voltage. It is recommended to consult a qualified electrician to ensure proper and safe rewiring of the water heater.
Can you hook 220 water heater to 110?
No, you cannot directly hook a 220V water heater to a 110V power source. The different voltage requirements will damage the water heater or cause it to function improperly. It's essential to match the voltage requirement of the appliance with the power source for safe and efficient operation.
What is the standard for Europe's electric current?
220V , 50Hz
Can you plug your 220V electric piano into a 110V socket?
No.
Can a 2-pole circuit breaker be used for 110V 220V or 440V?
All three, on 110V a split receptacle, on 220V a baseboard heater, on 440V a construction heater or similar resistive load.
How do you wire a 110v supply for 220v heaters?
A 220v heater has two 110v lines coming into it--either two 110v lines with a neutral, like a range, or two 110v lines with no neutral, like a water heater. Unless there's a fan in the system, they only use two wires. It's cheaper that way. If you have a DEDICATED circuit for each 220v heater--one where there's only one thing on the breaker--and you have at least 10/2 wire (unless the amps call for 8/2 or 6/2 wiring, which happens), you can install a two-pole breaker to feed 220v to the heater. If you're just trying to plug the heater into an outlet and get it to work, you've got a problem in that you can't pull 220v out of a 110v outlet no matter how hard you try. Sorry.
What size of breaker to use on a wall unit 220 heater?
The size of the breaker needed for a 220V wall heater depends on the current rating of the heater. Generally, for a 220V heater, a 20-amp breaker is common. However, it's important to check the manufacturer's specifications and local electrical codes for the appropriate breaker size.
Can we use an electric oven and a blender with 220V 50Hz in a 220V 60Hz source?
Yes, as long as the voltage is the same it will not cause any issues. The frequency, or Hertz, is only a problem for large electric motors and clocks.
What size breaker is needed for a 220 v hot water heater?
A 220V hot water heater typically requires a double-pole breaker rated at 20-30 amps, depending on the specific power requirements of the water heater. Make sure to consult the manufacturer's specifications or a qualified electrician to determine the appropriate breaker size for your specific unit.
How do you calculate the resistance of a heater element that's uses 220v and draws 11amps?
The equation you are looking for is R = E/I.
Will 240v heater work with 220v output?
Yes, a 240v heater will work with a 220v output. The slight difference in voltage should not significantly affect the heater's performance. However, it is always recommended to check the manufacturer's specifications to ensure compatibility.
What are the safety precautions to consider when installing a 220v garage heater?
When installing a 220v garage heater, it is important to follow safety precautions such as turning off the power supply, ensuring proper wiring and grounding, using appropriate tools, wearing protective gear, and following manufacturer's instructions carefully.
