0
What else can I help you with?
Can you do amplification without transistor and is it possible to design oscillator using diode?
Magnetic amplifiers and vacuum tubes don't need transistors to amplificate electricity current. You can get a transistor by two oppositely connected diodes.
What is blocking oscillator?
The oscillator which is blocked by using transformer is called a blocking oscillator. Generally, the primary is given to the base and secondary is given to the collector of the transistor used in the oscillator circuit.
Why the gain of pnp transistor is low?
it doesn't have to be. depends on design of amplifier using transistor.
Can I design a crystal oscillator using ua 741 op-amp?
yes
How do you design a RC coupled bjt amplifier using pnp transistor?
same as you would using an NPN, except the supply voltages are reversed
Can you do amplification without transistor and is it possible to design oscillator using diode?
Magnetic amplifiers and vacuum tubes don't need transistors to amplificate electricity current. You can get a transistor by two oppositely connected diodes.
What is blocking oscillator?
The oscillator which is blocked by using transformer is called a blocking oscillator. Generally, the primary is given to the base and secondary is given to the collector of the transistor used in the oscillator circuit.
Why the gain of pnp transistor is low?
it doesn't have to be. depends on design of amplifier using transistor.
Can I design a crystal oscillator using ua 741 op-amp?
yes
Is it possible to design a transistor by using two diodes practically?
No.
Phase-shift oscillator using pnp transistor?
A phase-shift oscillator using a PNP transistor consists of an RC network in the feedback path, a PNP transistor biased to operate in the active region, and a network of resistors and capacitors that provide the required phase shift for oscillation. The RC network introduces a 180-degree phase shift at the desired frequency, and the transistor provides the additional 180-degree phase shift needed for sustained oscillation. By properly selecting the values of resistors and capacitors, along with biasing the transistor correctly, a stable sinusoidal oscillation can be achieved.
How does a Colpitts oscillator work?
A Colpitts oscillator is the electrical dual of a Hartley oscillator. In the Colpitts circuit, two capacitors and one inductor determine the frequency of oscillation. The feedback needed for oscillation is taken from a voltage divider made by the two capacitors, where in the Hartley circuit the feedback is taken from a voltage divider made by two inductors (or a tapped single inductor). (Note: the capacitor can be a variable device by using a varactor). Oscillation frequency The ideal frequency of oscillation for the circuit is given by the equation: where the series combination of C1 and C2 creates the effective capacitance of the LC tank. Real circuits will oscillate at a slightly lower frequency due to junction capacitances of the transistor and possibly other stray capacitances
How do you design a RC coupled bjt amplifier using pnp transistor?
same as you would using an NPN, except the supply voltages are reversed
What is an oscillator and what are its main components?
oscillator is an electronic device used to generate wave form by using the concept of feed back.
How do you check transistor faulty or not?
the best way is to compeair the data sheet of that transistor to the readings of that transistor. . . . .and u can get the readings of that transistor by using a fungction genrator and a c.r.o
How do you obtain the variable frequency from converter using MC?
using voltage controlled oscillator
What are the instruments for the study of the gain of a two stage RC Coupled transistor amplifier?
depends on whether you would like calculate or measured results. if you want calculated resulted, then your best bet would be to use an oscilloscope. if you want calculated results, then there are formulas for finding out the voltage, current, impedance, and individual results from each component using the capacitive reactance, voltage, and type of transistor. are you using a summing transistor, inverting amplifying transistor, amplifying transistor, or a different transistor? also are you using DC or AC voltage or current? you need to tell me what type of transistor you are using?
