0
What else can I help you with?
How do you test a closed circuit?
we can make an open circuit by disconnecting the wire or break the circuit and a closed circuit is made by connecting all wires with the contents of the circuits.
Why light emitting diodes are good?
LED (light emitting diode) is an electronic component that generates light from the electrons flowing in one direction through it, in an electron circuit, possibly as part of a circuit board. In a circuit the light emission can be a short as a nanosecond. One or more LED's can be used to make light with a minimum of electricity. Modern applications are wide spread including optical sensor activators, calculator displays and automotive tail lights. LED's have come down in price and can last for tens of thousands of hours so have become an economical replacement for other lights in some applications.
What is the history of the electric circuit?
the history of the electric circuit is that the person who made it his name is jack kilby but the history is that the electric circuit was one of the easiest way was to make the electric circuit when the electricity went out. THE END
Where do you put your leads when checking continuity on a series circuit?
When checking continuity in a series circuit, you put your leads in series with the circuit or device being checked. You also make sure the circuit is deenergized and that it is open.
In a series connection if one component fails the whole circuit fails?
Yes. Open circuit. A: It depends on the failure type a short will not necessarily make an open circuit but rather a non functional circuit.
How do you make sure power is turned off?
if the switch in the circuit is switched off, the power is turned off on the object.
How do you get the dash panel lights to go on?
turn the lights on and make sure the dimmer is not turned all the way down
What should you do before leaving the house to ensure all the lights are turned out?
Before leaving the house, make sure to do a final walkthrough to ensure all lights are turned off.
How do you make a light circuit flash?
Wire in a turn signal flasher in series with the circuit you wish to flash. The flasher has two terminals. Just insert the flasher anywhere in the circuit. It will make/break the circuit to make the lights flash. This is considering that the circuit is 12 volts and not 120 volts.
How can I add can lights to an existing circuit?
To add can lights to an existing circuit, you will need to first determine if the circuit can handle the additional load. If it can, you can run new wiring from the existing circuit to the location of the can lights. Make sure to follow all local building codes and safety guidelines when installing the new lights. It may be helpful to consult with a licensed electrician to ensure the job is done correctly and safely.
Why does the engine make noise when the lights are turned on?
Alternator straining to maintain battery charge?
Why is there no power in the socket for the trailer lights?
Are you getting power to sockets? Make sure you have a good ground circuit
How can I wire multiple lights on one circuit diagram?
To wire multiple lights on one circuit diagram, you can connect the lights in parallel by running a single wire from the power source to each light fixture. This allows each light to operate independently without affecting the others. Make sure to use the appropriate gauge wire and follow safety guidelines when wiring multiple lights on a circuit.
How can I wire lights and outlets on the same circuit?
To wire lights and outlets on the same circuit, you can connect them to the same electrical circuit breaker. Make sure to follow local building codes and safety guidelines when doing electrical work. It is recommended to consult a licensed electrician for proper installation.
Why does the parking lights stay on in your subaru legacy after key is turned off?
its on timed delay, lights stay on or come on while exiting vehical to make it easier
How can I wire multiple lights to one switch in a single circuit?
To wire multiple lights to one switch in a single circuit, you can connect the lights in parallel by running a separate wire from the switch to each light. This allows the switch to control all the lights at once. Make sure to follow proper wiring guidelines and consult an electrician if needed.
How can I wire two lights to one switch in a single circuit?
To wire two lights to one switch in a single circuit, you can connect the lights in parallel by running a wire from the switch to each light fixture. This way, both lights will be controlled by the same switch. Make sure to follow proper wiring guidelines and consult an electrician if needed.
