answersLogoWhite

0

u dont flush the tolet

User Avatar

Wiki User

16y ago

What else can I help you with?

Continue Learning about Engineering

Why did Joseph Gayetty invent toilet paper?

To stop bacteria


How do I stop the toilet that keeps running after flushing The flapper is properly seated. The float needs to be pushed down to stop it?

either bend the arm of the float so it is partially submerged or adjust it with the screw that is attached to the float armature


Why would a toilet that has been working properly just stop flushing even though the tank and the bowl both fill up?

there can be many reasons and I will say my thoughts on just a few. 1. your toilet trap of the bowl is clogged with debris (toys, balls, etc) to fix = snake out toilet bowl or if necessary pull toilet bowl and snake backwards threw trap. 2. your tank flush flapper is closing to soon or your tank water level is not at right height to fix = change flapper or adjust water level height 3. your toilet arm before the vent is plugged because of back grade or debris clinging to the side of the drain pipe to test = pull toilet and run toilet water supply full on down threw toilet flange and see if any back flow. 4. your toilet main line is clogged from backgrade,roots,damaged pipe,etc but will let other fixtures slowly drain to test = camera toilet line from toilet flange out to street or septic or if no camera available then fill tub full and lav full and drain both at the same time and look at your lowest fixture trap to see if any back flow exists or open clean outs and if possible to see water flow .


What causes toilet tank to stop filling up with water?

The fill valve (ball valve UK) is siezed or clogged. As the water level rises, the float-ball rises and closes the valve when the water reaches the proper level.


How do you stop the toilet flapper from closing too quickly on flushing?

To prevent the toilet flapper from closing too quickly after flushing, you can adjust the chain connected to the flapper. Make sure there’s enough slack in the chain, allowing the flapper to stay open longer. Alternatively, you can add a weighted object to the flapper or replace it with one that has a slower closing mechanism. Additionally, check the flush valve seat for wear, as a worn seat can cause the flapper to malfunction.

Related Questions

How will you save the water?

Stop unnecessary flushes in the toilet. It definitely saves lot of water.


Is there a valve or gadget available to stop scalding when toilet flushes or freezing when sink is turned on?

There are temperature balanced shower bodies that will adjust the hot water flow when it senses that the cold water flow drops due to flushing the toilet.


Civic Hybrid rumbling sound when accelerating from a stop?

A rumbling sound when a Civic Hybrid is accelerating could be due to an exhaust leak. When there is an exhaust leak too close to the manifold it can create a deeper rumbling noise.


Do taking pregna-care stop hot-flushes?

No it isnt, you can take menovital or menopace


How can I turn the toilet water off to stop a leak?

To stop a leak in the toilet, locate the shut-off valve behind or near the toilet and turn it clockwise to close it. This will stop the flow of water to the toilet and prevent further leaking.


How can I turn off a toilet to stop water flow?

To turn off a toilet and stop water flow, locate the shut-off valve behind or near the toilet and turn it clockwise until it is fully closed. This will stop the water from flowing into the toilet.


What is the noise coming from the toilet when flushed?

Try adjusting the stop cock level. How far the stop cock goes up. This should stop it.


What is the purpose of an angle stop valve for a toilet and how does it function in the plumbing system?

An angle stop valve for a toilet is used to control the flow of water to the toilet. It is typically located behind the toilet and connects the water supply line to the toilet tank. The valve can be turned on or off to stop or allow water flow to the toilet. This is important for maintenance, repairs, and emergencies.


How do you stop an echo?

Scream "STOP! COME BACK!" out loud.


How can I stop a running toilet?

To stop a running toilet, you can adjust the float valve in the tank or check and replace the flapper if it is not sealing properly.


How can you quickly stop a running toilet in seconds?

To quickly stop a running toilet in seconds, lift the lid of the toilet tank and adjust the flapper or fill valve to ensure it is properly sealing.


How can I effectively stop a toilet from leaking at the base?

To effectively stop a toilet from leaking at the base, you can try tightening the bolts at the base of the toilet, replacing the wax ring, or contacting a plumber for professional assistance.