answersLogoWhite

0

Tools required: screw drivers, insulation tape - switch off your geaser, and plug out the power cable from the socket/power supply. Please also close the inlet water entry into your geaser. - remove the outer side of the geyser where the electrical connections are wired. This will need screwdrivers for most of the commercial geysers - Now you will see a big knob with temperature markings (usually 0 - 80 degree celsius) coming out of your geaser tank. - slowly track the electrical connections that is going into the thermostat and disconnect them (usually 2 of them) - Now pull the thermostat out - you will see a long rod coming out from the geaser. Now you are successful in pulling your thermostat out. - Now you want me to reverse-repeat the setps for plugging in the new thermostat in ? :-) - BTW...please note to set the temperature mark in the thermostat appropriately. Usually use the same as it was there in your older thermostat. - after plugging in the new thermostat, and you connect the electrical wiring, close the geyser (with whatever you removed) and open the inlet water entry. You need to plugin the power cable and switch it on again. Hope you find this useful, the new thermostat makes the geyser happy ! cheers, Harish

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How do you know if your geyser thermostat is not working?

Disconnect power to geyser and remove the thermostat. Turn heat selector to maximum and with the thermostat removed from the geyser and electrical wiring, test for continuity between the input and output sides of the (L)ive side. If there is continuity the thermostat is ok and the fault may then lie with the element.


How to test a thermostat to ensure it is functioning properly?

To test a thermostat, you can use a multimeter to check for continuity in the thermostat's contacts. You can also submerge the thermostat in hot water to see if it opens and closes properly.


How do I Replace an electric geyser element?

First of all make sure that the power to the geyser is off, test to make sure. you then need to drain the geyser. make sure that the tap supplying the inlet pipe is turned off, open the valve on the drain cock slowly making sure that the water is falling into the drip tray, open the valve as much as is needed or all the way if possible. This will take anywhere between 30 to 60 minutes to drain. then remove the power cable to the thermostat and or to the element. in some geysers the thermostat will sit next to the element and in others the thermostat will be part of the element. in the latter you will need to remove the thermostat by simply pulling it away from the element. you will now need a geyser spanner to be able to remove the element, in some instances you will need quite a lot of leverage as the elements do tend to sit pretty tight. when the element is lose and out make sure that the rubber seal came off properly as well. you'll need to clean it thouroughly before inserting the new element with its new rubber seal, screw it back into place, ensring that you don't cross the thread as you're doing this and fasten properly, insert the thermostat again and reconnect the power cables. do not switch on the power before the geyser is full otherwise you will burn the element out. turn on the water tap to the geyser and open all the hot water taps in your house. the geyser will be properly filled when the water is flowing from all the taps without any air bubbles. you may now switch on the power.


How can I test a refrigerator thermostat to ensure it is functioning properly?

To test a refrigerator thermostat, you can use a multimeter to check for continuity in the thermostat. Set the multimeter to the ohm setting and place the probes on the thermostat terminals. If the reading shows continuity, the thermostat is functioning properly.


How can I test a hot water heater thermostat to ensure it is functioning properly?

To test a hot water heater thermostat, you can use a multimeter to check for continuity in the thermostat. First, turn off the power to the water heater. Then, remove the access panel to expose the thermostat. Use the multimeter to test the thermostat's terminals for continuity. If there is no continuity, the thermostat may be faulty and needs to be replaced.


How can I test the thermostat on an electric water heater?

To test the thermostat on an electric water heater, you can use a multimeter to check for continuity and proper functioning. First, turn off the power to the water heater. Then, remove the access panel to expose the thermostat. Use the multimeter to test the thermostat's terminals for continuity. If there is no continuity, the thermostat may be faulty and need to be replaced.


How do you balance the pressure of your geyser?

To balance the pressure of your geyser, you can adjust the temperature setting on the thermostat to regulate the flow of hot water. You can also check the water pressure regulator on the main water supply line to ensure it is set to the appropriate pressure. Regular maintenance, such as descaling the geyser, can also help maintain proper pressure.


What is a natural hot spring that occasionally sprays water steam above the ground?

A hot spring that naturally shoots steam and boiling water is called a geyser.


What causes geysers to erupt?

the most common cause for a geyser to erupt is due to a tempreature and pressure problem. many plumbers who dont know how to install geyers properly, plug off the TP safety valve outlet (Temp and Pressure), what happens, the thermostat in the geyser fails and cannot control the tempreature inside the geyser, causing the geyser to over boil, which then creates extra pressure (because of the steam) within the geyser, so when that safety outlet is plugged off the geyser takes an enormous amount of strain, and then it finally explodes. it can be devestating and has known to rip roofs off houses.


Is castle geyser a geyser or a type of geyser?

Castle Geyser is a specific geyser located in Yellowstone National Park. It is a type of cone geyser, named for the cone structure that surrounds the vent where the water erupts.


What type of geyser is the Yellowstone geyser?

A Conical Geyser (or cone)


How can I test an electric water heater thermostat to ensure it is functioning properly?

To test an electric water heater thermostat, you can use a multimeter to check for continuity and proper voltage. First, turn off the power to the water heater. Then, remove the thermostat cover and use the multimeter to test the thermostat terminals for continuity. If there is no continuity, the thermostat may be faulty and needs to be replaced. Additionally, you can check the voltage across the thermostat terminals to ensure it is receiving power. If there is no voltage, there may be an issue with the electrical supply to the thermostat.