Actually you would use a mud bed. Appr. 3/4 inch but will vary as no floor is level. Installing a marble floor is not for the average person to do. To tell you the truth most TILE installers have no idea what they are doing. Marble as opposed to tile is set with little to no grout joint. Also SANDED GROUT is a very big NO NO.
To install marble tiles, you first need to lay out your tiles to determine the correct position and which tiles need to be cut. It is usually around the corners or near your doorway.
After that, use a notched trowel to apply a layer of thin adhesive. Lay the tiles allowing for some tile separation and leave it to dry overnight. Once it is dry, you can use concrete to fill in the gaps. Use the squeegee to spread it and wipe the excess away. The last step is to wash the surface of the marble tiles after you are done.
MOST TILE installers do not know what they are doing!!! Marble is a porous stone, unlike a ceramic tile, it will absorb water and moisture. If you use a "notched trowel" you will leave spaces for water to settle under the stone. That water has to escape. So it will do so through to the stones surface. This escape of water will leave a haze on the stone that does not wipe away. It is called effloresence. In some cases the stone will spall. Which is basically the stone flaking away. Not all types of marble are prone to this problem but some more than others. Verde aka green marble is one of the most common for effloresence and spalling. I REPEAT Installing a marble floor is not for the average person to do.
basalt, marble
it eamns the type of floor desired. it can be of wood, tiles, terazzo, marble etc.. :)
Granolithic Floor is a marble type mosaic floor finish that uses Portland cement as base materials. It has a characteristics of durability, beauty and variety installed in either by: a. Monolithic or cast in place - means massively, solid, single and uniform floor finish cast in place. A mixture of cement and marble chips to a proportion of 1:3 is casted on top of a rough floor slab surface to an average thickness of 1.25 cm. the floor is then grinded after it has attained sufficient hardness to withstand abrasion and vibration caused by the grinding machine. Grinding of the floor surface should not be allowed earlier than 48 hours after casting. b. Pre-cast - refers to granolithic tiles in various dimensions hydraulically pressed and molded in a factory. The distinctive difference between the cast in place and the pre-cast installation is the manner and place of casting or molding. The former being installed on site and the latter at the factory site. Thus, pre-cast is installed in a tile form while cast in place is installed in a fresh mixed form.
You will need to sand the floor to give the thinset something to stick to.
gas insulated substations are installed especially where floor area available is limited and maintenance cost is more
No, acetone will etch marble.
No, one does not need to use special cleaning techniques to clean a marble floor. Cleaning a marble floor can be done just like cleaning every other type of floor.
The best techniques for effectively cleaning a marble floor using a marble floor cleaner are to first sweep or vacuum the floor to remove any debris, then dilute the cleaner according to the instructions on the bottle. Next, mop the floor with the cleaner, making sure to wring out the mop well to avoid excess water on the marble. Finally, dry the floor with a clean, dry cloth to prevent streaks or water spots.
To clean a marble floor effectively, start by sweeping or vacuuming to remove debris. Then, use a mild detergent or specially formulated marble cleaner with warm water to mop the floor. Avoid using acidic or abrasive cleaners that can damage the marble. Rinse the floor thoroughly and dry it with a soft cloth to prevent water spots. Regularly seal the marble to protect it from stains and maintain its shine.
marble
with floor shine
Some of the best marble floor cleaners on the market include products like Black Diamond Marble Tile Floor Cleaner, StoneTech Revitalizer Cleaner and Protector, and Granite Gold Stone and Tile Floor Cleaner. These cleaners are specifically formulated to clean and protect marble floors without causing damage.
To effectively clean marble floor tiles, start by sweeping or vacuuming to remove debris. Then, use a mild detergent or specially formulated marble cleaner with warm water to mop the floor. Avoid using acidic or abrasive cleaners that can damage the marble. Rinse the floor thoroughly and dry it with a soft cloth to prevent water spots. Regularly seal the marble to protect it from stains and maintain its shine.
According to Newton's First Law of Motion, the marble will remain at rest unless acted upon by an external force. In this case, if no external force is applied to the marble, it will continue to stay still in the middle of the floor.
Using marble for a shower floor offers benefits such as durability, elegance, easy maintenance, and resistance to water damage.
cost to remove tile floor
basalt, marble