0
What else can I help you with?
Why thermionic valve or vacuum tube are evacuated?
because if it was heated in open air it would burn up
Is the propeller shaft the same as the stern tube shaft?
The propeller shaft in a boat engine is fastened to the flywheel by bolts, and it passes through the boat's thrust block and is aligned with the shaft tunnel. It also passes through the stern tube to drive the propeller. The stern tube shaft itself holds the "prop" shaft in place and shut off the open end when it pierces the aft hull. It is commonly manufactured as cast iron and welded into the frame of the stern of the ship.
How do you open a hex bug nano tube?
You pull the tab til the bottle is separated from the paper, then you twist the cap off.
How do you load a Glenfield Model 60?
Unscrew the magazine tube (located near the muzzle of the gun) and pull it out until the ammunition feed port (located on the bottom of the magazine tube) is open. Feed the ammunition in primer first and drop down the tube. Once loaded, push the tube back down and screw to secure. Cycle the action to load the ammo. Be careful and have fun.
What is the function of the inductor in a fluorescent tube light circuit?
Without an inductor in series with the tube, the plasma in the tube would simply short-out the service wires. That would always cause the circuit's protective fuse to blow - or its circuit breaker to trip - to cut off the supply of current to the tube. If that happened the tube light would never be able to perform its intended purpose, which is to continue running - and giving out a continuous light - for long periods of time.So a high-inductance choke must be used in circuit with the starter and the tube for two reasons:firstly the choke generates a high voltage pulse across the tube when the starter's contacts open. That pulse causes the gas in the tube to ionise and become a low-resistance plasma andsecondly, because it is wired in series with the tube, the choke greatly reduces the current drawn by the tube once it contains the low-resistance plasma.The starter is a special kind of switch: its contacts are made of a metal alloy which heats up and bends soon after a voltage is applied, causing the switch contacts to open.
How do you load a winchester06-22cal long short-long rifle?
under the barrel is a long tube. at the end of the tube is a knob. twist the knob to lossen it then with draw the inner tube. next back 10 rounds of 22 long or shot into the tube. do not put shells in head first, rear first. replace the inner tube and lock it in place. pump the rifle and your 06 is loaded....................
What is patent tube?
A tube that is open or free of obstruction.
Where does digested food take place?
It mainly takes place in our small intestine.The 20 feet long coiled tube...
Will a 25hp two stroke pull a tube good on a 14 ft aluminum boat?
yes it will. it will be a lot easier with a smaller tube and smaller rider but as long as the tube is designed to be pulled (ie flat bottom, not open tube) you will be just fine.
What tubes open into the nasopharynx?
EUSTACHIAN TUBE or auditary tube.
Why flex head forward when inserting a ng tube?
this position helps place the Ng tube into the esophagus instead of the trachea by slightly blocking the airway and giving an open unresisting path into the esophagus.
How do you open water blaster tube?
you have to twist open at the top
How can avoid stucking hot tube together?
To prevent a hot glue tube from becoming stuck, always recap the tube securely after use and store it in a cool, dry place. Try to avoid leaving the tube lying flat after using it, as this can cause the glue to dry around the cap and nozzle, making it difficult to open. If the tube does become stuck, soaking it in warm, soapy water can help loosen the dried glue and make it easier to open.
Does tube have a long U?
Tube has the long OO sound to rhyme with boob.
What is the function of a pollen tube?
The long tube
How many centimeters long is this tube?
What tube
What is capillary tubes?
In chemistry... it's a thin open-ended glass tube for collecting small amounts of liquid. Inserting one end of the tube into liquid allows the liquid to flow upqwards. When the liquid reaches a suitable height, a finger placed over the open end (towards the top) holds the liquid in the tube - for transferring from one place to another.
