answersLogoWhite

0

What else can I help you with?

Continue Learning about Engineering

What do you need to join pvc pipes together?

You use PVC glue or cement.It's really quite easy.First you clean the pvc with solvent,then you put on the pvc glue.You want a little more than will cover the joint,but not enought to drip.You hold it together for about a minute.Wait an hour before you run water through it.


How do you repair a small puncture hole from a nail in PVC pressure water pipe embedded in cement flooring?

If the hole is clear of the concrete get a little bit of pipe 25mm or an inch and cut it along the length so that you have a ring that opens up. Get some PVC primer and PVC solvent cement . use the primer to clean the outside of the pipe with the hole in it and the inside of the patch. put solvent cement on the pipe around where the patch is going. stretch the ring so it opens up and covers the hole and hold it in place. you can do this with a suitable hose clamp. wait a couple of hours before use. if you can reach the inside of the pipe you can use a similar procedure,


How long PVC solvent cement take to dry?

Less than a minute. Make sure you dryfit the pvc fittings to ensure everything is where you want it. Slather on purple primer, then slather on the cement and twist it on and hold it for 30 seconds until it sets. In less than a minute you won't be able to move it.


Can you repair a bicycle tire with PVC cement vice contact cement?

You can repair small punctures with PVC cement, but the results will not be optimal. To repair a tire (inner tube), you need a solvent that will disolve a bit of the top layer of the rubber tube and the bottom layer of the patch. Then, as the solvent dries, the two, together with the added rubber in the rubber cement, become one. this gives a strong, flexible, air tight seal. The solvents in PVC cement fill the bill for disolving the rubber. But instead of a flexible rubber base, it's relatively inflexible PVC. Your repair will be air tight, but far less flexible than it would be with rubber cement. This may, in the long term, lead to stress failure at the edge of your patch.


Is there anything that will dissolve plumbers glue from a shower that has been glued to the metal pipe?

This is quite confusing. -If you mean "plumbers glue that has been glued to the metal pipe" as opposed to "a shower that has been glued to a metal pipe" , then it's a little easier. -Any plumbers glue, be it ABS, PVC or CPVC glue, or Transition cement can be peeled off metal pipe.In future PLEASE say what exactly you mean by "metal pipe" - copper, - galvanised, or which other metal, and please -Name your glue - Most plumbers commonly use at least 4 different glues.

Related Questions

Can ABS and PVC be glued together?

No, ABS and PVC cannot be glued together using standard adhesives. Specialized solvent cement is required to bond these two types of plastic.


How can I unglue PVC cement effectively?

To unglue PVC cement effectively, you can use a solvent specifically designed for PVC, such as acetone or PVC primer. Apply the solvent to the glued area and allow it to soften the adhesive. Then, carefully peel or scrape off the softened PVC cement. Be sure to follow safety precautions and work in a well-ventilated area when using solvents.


Can ABS be glued to PVC?

No, ABS cannot be effectively glued to PVC because they are made of different materials that do not bond well together.


How do you remove a PVC flange glued to a PVC drain pipe?

pvc flange if glued properly can not be detached you just need to cut it and fix up a new one if the old flange is useless. www.pvcpipe.in


What glue should be used to seal flexible PVC into concrete?

None. PVC is not made to be glued to concrete.


What is the solvent for PVC?

The solvent commonly used for PVC is tetrahydrofuran (THF). It is often used to dissolve PVC for various applications such as adhesive formulations or polymer processing.


Can you glue ABS to PVC materials?

No, ABS cannot be effectively glued to PVC materials due to their different chemical compositions.


Can you glue PVC to ABS materials?

No, PVC cannot be effectively glued to ABS materials due to their different chemical compositions.


Can you glue PVC to CPVC?

No, PVC cannot be glued to CPVC because they are made of different materials and require specific types of adhesive for bonding.


How can I remove a glued PVC pipe effectively?

To remove a glued PVC pipe effectively, you can use a heat gun to soften the adhesive and then twist and pull the pipe apart. Be sure to wear protective gear and work in a well-ventilated area.


How do you separate two pieces of abs glued with PVC glue?

You just pull it apart really hard. PVC glue will not effectively glue ABS.


How can I separate glued PVC pipe?

To separate glued PVC pipe, you can use a heat gun or a hair dryer to soften the adhesive. Once the adhesive is softened, twist and pull the pipes apart carefully. Be cautious not to damage the pipes during the separation process.