answersLogoWhite

0

6

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Engineering

Why there are two type of connection on motor terminals?

Motor terminals typically feature two types of connections—star (Y) and delta (Δ)—to accommodate different voltage and current requirements during operation. The star connection allows for lower voltage and higher current, making it suitable for starting the motor, while the delta connection enables higher voltage and lower current for efficient running at full load. This dual connection system enhances flexibility, allowing the motor to perform optimally under varying conditions.


How many contactors using in star connection of motor?

two contecter <<>> There are three contactors used in a Star Delta configuration.


Where do you use star-star connection in electrical system?

i think its use for 3 phase connection.


Can an 2 farad capacitor still be used if the terminals were crossed at connection?

I Rather not think that you can buy 2 farad capacitor and no the terminals must follow polarity guidelines.


Why are there six terminals in a three-phase induction motor?

In 3phase induction motor, stator winding splited into 3windings (Each winding conductor size, no of turns etc are equal to each other). So 3 windings have 6terminal. Generally all 6 terminals are taken out for termination on 5HP and above rated 3phase motors. So, that motor can be started with star / delta starters to reduce starting current (DOL starter does not reduce starting current). Major advantage is It is easy to change the connection (STAR / DELTA) acoording to the purpose going to be used. Also starting and ending terminal to be marked properly.

Related Questions

Why we get the 0 level in trans farmer when we use delta to star connection when you get the 220 volts at each terminals of star connection of transformer how we get 0 level or neutral equals to 0?

A: In the USA there is D delta connection or Y connection. The Y center point may not be zero if there is circulating current due to mismatch of the phases


Why there are two type of connection on motor terminals?

Motor terminals typically feature two types of connections—star (Y) and delta (Δ)—to accommodate different voltage and current requirements during operation. The star connection allows for lower voltage and higher current, making it suitable for starting the motor, while the delta connection enables higher voltage and lower current for efficient running at full load. This dual connection system enhances flexibility, allowing the motor to perform optimally under varying conditions.


Star-star connection of transformer?

Star Star TransformerStar Star Transformer is formed in a 3 phase transformer by connecting one terminal of each phase of individual side, together. The common terminal is indicated by suffix 1 in the figure below. If terminal with suffix 1 in both primary and secondary are used as common terminal, voltages of primary and secondary are in same phase. That is why this connection is called zero degree connection or 0o - connection.If the terminals with suffix 1 is connected together in HV side as common point and the terminals with suffix 2 in LV side are connected together as common point, the voltages in primary and secondary will be in opposite phase. Hence, Star Star Transformer connection is called 180o - Connection, of three phase transformer.Vikram Meena


What causes hot positive battery terminals?

Dirty connection


What is the definition of star connection?

The definition of star connection is a connection of the ends of phase windings at the star point.


How do you convert star delta connection to delta star connection?

hahahaa


How much is the potential difference between the terminals of a connection wire?

The potential difference between the terminals of a connection wire is determined by the voltage difference applied across the wire. This voltage difference creates an electric field within the wire that causes charge carriers to move and establish a potential difference between the terminals.


How many contactors using in star connection of motor?

two contecter <<>> There are three contactors used in a Star Delta configuration.


Where do you use star-star connection in electrical system?

i think its use for 3 phase connection.


Can an 2 farad capacitor still be used if the terminals were crossed at connection?

I Rather not think that you can buy 2 farad capacitor and no the terminals must follow polarity guidelines.


How many terminals does Heathrow currently have?

Heathrow has two terminals


Can you run a motor in star?

Only if it provides you with that option, by allowing access to its terminals.