0
I don't know.
During the clean up operations, there was many suggestions of mopping up oil using sponges, mats made of hair, and maybe sawdust. Any absorbing material should be able to remove some oil from water. Small spills of oil or other pollutants in calm water, may be more effectively cleaned up using these mats. Material or mats that absorbs oil must then be picked up and creates a very large disposal problem. Skimmers seemed to work best.
What else can I help you with?
What temperature does concrete need to be to harden?
all things that need to dry are based on 72 degrees concrete needs 30 days to fully cure.
What mix is used for dry lean concrete?
Dry lean concrete is used as a sub base for structural concrete. It contains much less cement and more sand compared to structural concrete.
How do you pour concrete on old concrete?
What you need to do first is to check if you have that room near the threshold of the door for that extra concrete(which is minimum of 3.5" inches) then you need to remove the top surface of the old concrete to be rough surface don't break too much just about an 1"wash clean and let it dry and only then to install the new concrete.
How much is concrete?
Bags of dry powered mix concrete are usually just a couple of bucks each for 80lbs.
Why do you need to flush a floor drain periodically?
Floor drain trap can dry out leaving no seal, allowing sewer gases to escape.
Can you store Stargazer Lily's in sawdust?
You can store Stargazer Lilies in sawdust or dry straw, as long as you keep them in a dark, cold place.
How can I safely dispose of a sawdust bag used for a table saw?
To safely dispose of a sawdust bag used for a table saw, you should first allow the sawdust to completely dry out to reduce any potential fire hazard. Once dry, you can dispose of the bag in your regular household waste or check with your local waste management facility for any specific guidelines on disposing of sawdust. It is important to avoid inhaling the sawdust and to handle it with care to prevent any potential health risks.
How can I make wood filler from sawdust?
To make wood filler from sawdust, mix the sawdust with wood glue or a similar adhesive until it forms a thick paste. Apply the mixture to the wood surface and let it dry before sanding it smooth.
How can I make wood putty from sawdust?
To make wood putty from sawdust, mix the sawdust with wood glue until a thick paste forms. Adjust the consistency by adding more sawdust or glue as needed. Apply the putty to fill in gaps or cracks in wood surfaces, then sand it smooth once dry.
How much does one cubic meter of sawdust weigh?
one cubic meter stone dust equals to how much metric ton stone dust ?
How can I make stainable wood filler using sawdust?
To make stainable wood filler using sawdust, mix sawdust with wood glue until it forms a thick paste. Apply the mixture to the wood surface, let it dry, then sand it smooth before staining.
How to effectively clean up sawdust?
To effectively clean up sawdust, use a vacuum with a HEPA filter or a damp cloth to wipe surfaces. Avoid using a broom or dry cloth as they can stir up dust. Dispose of sawdust in a sealed bag to prevent spreading.
How can I make wood filler using sawdust?
To make wood filler using sawdust, mix the sawdust with wood glue or a similar adhesive until it forms a thick paste. Apply the mixture to the wood surface and let it dry before sanding it down for a smooth finish.
How can you get the smell of spilled ranch dressing out of a suit when neither Febreez nor dry cleaning quite gets the job done?
Have it dry-cleaned.
How can I effectively clean up sawdust in my house?
To effectively clean up sawdust in your house, use a vacuum cleaner with a HEPA filter or a damp cloth to wipe surfaces. Avoid using a broom or dry cloth as they can stir up the dust. Dispose of the sawdust in a sealed bag to prevent it from spreading.
How can I create a DIY wood filler using sawdust?
To create a DIY wood filler using sawdust, mix the sawdust with wood glue or a similar adhesive until it forms a thick paste. Apply the mixture to the wood surface and let it dry completely before sanding it down for a smooth finish.
How can I create a homemade wood filler using sawdust?
To create a homemade wood filler using sawdust, mix the sawdust with wood glue or a similar adhesive until it forms a thick paste. Apply the mixture to the wood surface and let it dry completely before sanding it down for a smooth finish.
