answersLogoWhite

0

The cost to knock out a wall and install a sliding glass door varies. The cost is determined by the cost of materials, and the cost of labor. A professional can give an accurate estimate for the deconstruction and install.

User Avatar

Wiki User

11y ago

What else can I help you with?

Continue Learning about Engineering

How do you level and plumb a sliding glass door?

The question is a little confusing. If the floor is level you just put the bottom of the sliding glass door track on the floor. With the stationary section of glass in place the one side of the door should now be quite plumb and all you have to do is attach that part of the frame to the house. On the other hand, if you are asking about a door that is already installed and are wanting to plumb the slider, there should be two screws near the bottom of the door sides and two screws near the top. In order to turn the bottom screws it may be necessary to relieve pressure from the top screws and slightly lift the bottom of the door. Adjust the door so that it is parallel to either the stationary glass or the side frame, whichever side has the locking mechanism. LEVEL equalls left to right.....so place door in a bed of silicone greater than the amount the existing floor is out and shim the appropriate side up until the top of door from left to right is level PLUMB is vertical....... top to bottom and left to right with in one side of the jamb;;;jamb must be plumb in both direction and on both sides of jamb within a straight lin of itself for it to be SQUARE....


Are doggie doors difficult to install?

A doggie door can be difficult to install according to the person that is intalling it. They can be difficult if you don't read the instructions. Reading the instructions carefully before putting the door in can be very useful.


How much would it cost to install an entry door and a storm door?

hey it would cost approximately $80 000!


Can you drill a hole in a door and install a dead bolt lock if the door is fire rated?

The deadbolt should not affect your fire rating.


What is a herculite door?

A herculite door was a particular manufacturer of a frameless glass door. This would normally consist of 1/2" tempered glass with the vertical edges polished. Tops and bottoms are pivoted by either patch fittings or full width shoes, often with polished metal cladding. These are hi profile doors you might see at a lobby, or mall entrance, or perhaps an executive office. People often recognize frameless glass doors as the age old term herculite door.

Related Questions

What is the average price to install a sliding glass door in Des Moines?

It is really impossible to tell you the average price of sliding glass door installation. This is because there are too many factors that effect the price such as the size, style and kind of glass you are installing.


How can I replace the sliding glass door rollers?

To replace sliding glass door rollers, you will need to remove the door, take out the old rollers, install new rollers, and then reattach the door. Make sure to follow the manufacturer's instructions and use the appropriate tools for the job.


How can I replace the rollers on a sliding glass door?

To replace the rollers on a sliding glass door, you will need to remove the door from the track, take out the old rollers, and install the new ones in their place. Make sure to adjust the new rollers properly to ensure smooth operation of the door.


What is the standard height of a sliding glass door?

The standard height of a sliding glass door is typically 80 inches.


How long is a sliding glass door?

A sliding glass door is typically around 6 to 8 feet in length.


How can I install curtains on a track for my sliding glass door?

To install curtains on a track for your sliding glass door, first measure the track length and purchase curtains that fit. Attach the track to the ceiling or wall above the door. Slide the curtains onto the track and secure them in place. Adjust the curtains as needed for proper coverage and functionality.


How can I replace a sliding glass door lock?

To replace a sliding glass door lock, you will need to remove the old lock by unscrewing it from the door. Then, you can install the new lock by following the manufacturer's instructions and securing it in place with screws. Make sure the new lock is compatible with your door before installing it.


What kind of blinds can I use on a sliding glass door?

For a sliding glass door, you will generally want to choose vertical blinds.


What is the width of a sliding glass door?

The width of a standard sliding glass door is typically between 60 to 72 inches.


What kinds of sliding glass door locks are child proof?

Some child proof door locks for a sliding glass door come in the form of straps, bars, and locks positioned higher than the child's reach. These are sold in stores or over the internet and many are easy to install.


How can I repair a sliding glass door that is not sliding properly?

To repair a sliding glass door that is not sliding properly, you can try cleaning the tracks, lubricating the rollers, adjusting the alignment of the door, and replacing any damaged rollers or tracks.


What is the standard length of a sliding glass door?

The standard length of a sliding glass door is typically between 60 to 72 inches.