0
transistor size depends on its channel length, that is the length of the region in which a transistor act as an electron tube.
the shorter the region, the lowest the resistance, the fastest the transistor, etc...
so, it is always good to scale transistor size.
problem is that you have to apply a 'good' electrical field in the channel, in order to drive a good 'ON' or 'OFF' state for your transistor. that's why it's not easy to scale their size.
What else can I help you with?
What is difference between transistor biasing and connection?
Transistor biasing is a function of implementing a DC support circuit that places the transistor in an electrical region that produces the desired output signal in relation to its input signal, according to its design specification. A transistor can be biased to create a linear amplified signal proportional to its input. Biasing can also place the transistor into an easily saturated condition to propagate clipped binary output relative to its input. Biasing refers to the component configuration designed around a specific transistor family. Connection refers to the simple function of making an electrical junction between two conductors.
A new programmer whom you are training is writing a C program and wants to place comment lines in the program what characters should be used at the beginning and end of the comments?
if single line comment just place // before for single line comment else if multiple line denote as like this /*............................. ..............................*/ Strictly speaking, // is non.standard in C only in C++
How has thyristor term been coined?
The term "thyristor" was coined from the terms "thyratron" and "transistor". A thyratron was a gas-filled vacuum tube switch - when triggered, it developed a low impedance path from cathode to anode, and that path stayed in place until the current through the tube ceased - you couldn't "turn it off". The thyristor was seen as a "solid-state thyratron".
How do you find emitter base collector terminals in transistor?
I know only two types of transistors, one is with a metal head, another one with a plastic covering. For the metal one, you could see a little protruding metal piece, the pin near it is EMITTER, the one which is away from that is COLLECTOR and the other is BASE For the plastic one, one face of it will be flat, make it lie down such that the flat side is touching the ground, now the middle one is BASE, right one is COLLECTOR, left one is EMITTER For all others where both the sides are flat, check for a dot or circle on it, place the transistor so that you the dot or circle faces you, now the middle one is BASE, right one is COLLECTOR and the other is EMITTER
Can CN100 be used in place of CL100 transistor?
CN100 and CL100 transistors are not directly interchangeable due to differences in their specifications and intended applications. While both may be designed for similar functions, such as amplification, their electrical characteristics (like current rating, voltage rating, and gain) must be closely examined to ensure compatibility in a specific circuit. Always refer to the datasheets for both transistors to determine if one can substitute for the other in your application.
Does CL100 transistor can be use at the place of SL100 transistor?
yes.
What is the equivalent component to use in place sl100 transistor?
What is the equivalent component to use in place sl100 transistor? ...
What have taken the place of glass valves in radios?
transistor
What is Q point of a transistor?
Q point which is quiscent (silent) point is the operating point of a transistor where the variations of collector current and collector-emitter voltage take place when signal is applied.
What is difference between transistor biasing and connection?
Transistor biasing is a function of implementing a DC support circuit that places the transistor in an electrical region that produces the desired output signal in relation to its input signal, according to its design specification. A transistor can be biased to create a linear amplified signal proportional to its input. Biasing can also place the transistor into an easily saturated condition to propagate clipped binary output relative to its input. Biasing refers to the component configuration designed around a specific transistor family. Connection refers to the simple function of making an electrical junction between two conductors.
What is the Effect of collector resistance in emitter follower circuit?
Colector resistance in an emitter follower circuit serves to place a limit on how much current can be supplied by the transistor. Often, the resistor is sized so that a short circuit in the load does not cause the transistor to fail.
How does a npn transistor switch work to switch a load on and off?
let's insert a transistor in place of the switch to show how it can control the flow of electrons through the lamp. Remember that the controlled current through a transistor must go between collector and emitter. Since it is the current through the lamp that we want to control, we must position the collector and emitter of our transistor where the two contacts of the switch were. We must also make sure that the lamp's current will move against the direction of the emitter arrow symbol to ensure that the transistor's junction bias will be correct as in Figure below(b).
What is the word for a number that has a digit in the tens place hundreds place or beyond?
There is no single word.
In the movie Doubt a transistor radio is confiscated but were these available in the late fifties?
The movie actually takes place in 1964, and transistor radios made their explosive entry into the West in 1957.http://en.wikipedia.org/wiki/Transistor_radiohttp://en.wikipedia.org/wiki/Doubt_%282008_film%29
Where can you find a replacement for a transistor number umt3584?
Check this place. Others do exist offering such a component. www.cmbcomp.com/p/l35.htm Good luck.
What is 0.3 as a reduced fraction?
3/10. You can tell because in 0.3 is in the tenths place.
What is the place value or 84.61?
A place value is relevant in the context of a single digit within a number. For a whole number it has no meaning. A place value is relevant in the context of a single digit within a number. For a whole number it has no meaning. A place value is relevant in the context of a single digit within a number. For a whole number it has no meaning. A place value is relevant in the context of a single digit within a number. For a whole number it has no meaning.
