0
To calculate the cubic capacity of the bucket of an excavator, measure the internal dimensions of the bucket: length, width, and depth. Use the formula for volume, which is length × width × depth. If the bucket is a more complex shape, you may need to approximate it to a rectangular prism or use water displacement for more accurate results. Finally, convert the volume from cubic inches or centimeters to cubic yards or cubic meters as needed.
What else can I help you with?
How much concrete mix use in 5 cubic meter 1 bucket cement 4 bucket sand 8 bucket 40mm metal?
To calculate the total concrete mix for 5 cubic meters with the specified ratio of 1 bucket of cement, 4 buckets of sand, and 8 buckets of 40mm metal, first determine the total parts: 1 + 4 + 8 = 13 parts. For 5 cubic meters, each part would be approximately 0.385 cubic meters (5 / 13). Therefore, you would need about 0.385 cubic meters of cement, 1.54 cubic meters of sand, and 3.08 cubic meters of 40mm metal. Adjust bucket sizes accordingly to match these volumes based on the bucket's capacity.
How calculate capacity of refrigeration compressor?
To calculate the refrigerant charge in a car, you must check its AC service valves under the hood in a car that is turned off using manifold gauges. Attach its red hose to the high-pressure gauge and the blue hose to the low-pressure gauge. Open the pressure valve on both sides. The normal low should be 25 to 45 psi. The normal high should be 225 to 250 psi.
Calculate the cubic capacity of a 6 cilynder engine with a bore of 85mm and astroke of 90mm?
no of cylinders = 6 bore = 85 mm =8.5cmstroke = 90mm =9 cmbore area = bore * bore * pi/ 4 (pi=3.14159)volume of 1 cylinder = bore area * strokeengine capacity = volume of 1 cylinder * no of cylindersbore area = 8.5 * 8.5 * 3.14159/ 4=56.745 square cmvolume of 1 cylinder= bore area * storke=56.745*9=510.7 cubic cm (cc)engine capacity =volume of 1 cylinder * no of cylinders=510.7 * 6=3064.22 cc
What is the meaning of throughput in gas pipelines?
This term is an equivalent of capacity; expressed for example in cubic meters of gas to second.
How can you calculate for 1 cubic concrete steel requirement for raft foundation?
concrete and cementtarmacsmooth roadgood roadsfriction
How do you calculate excavator production per hour?
Essentially, excavator productivity is typically measured by the volume of loose or rock soils the machine can displace in a hour of continuous operation. Understand the formula for calculating excavator productivity. The formula is as follows: Q = (60*q*z*n*kf) / kl, where Q is the productivity of the excavator, q is the capacity of each rotor bucket in cubic feet, z is the number of buckets on the wheel and n is the speed of rotation of the rotor, measured in revolutions per minute. kf stands for the filling factor of a bucket while kl represents the soil-loosening factor. Gather the data. Typically, you can get the date for the capacity of each rotor bucket in cubic feet, the number of buckets on the wheel and the speed of rotation of the rotor from the operator's manual of your excavator, supplied by its manufacturer. The filling factor of the bucket and the soil-loosening factor can be determined experimentally. The filling factor, ranging from 0 to 1, determines the degree of the excavator bucket's utilization. For example, whether it is half-full or three-quarters-full determines the excavator bucket's utilization. To determine the soil loosening factor, which is always greater than 1, calculate by how much the density of the soil in the ground is greater than the density of the excavated soil. For example, if the soil loosens by 10 percent, the soil-loosening factor is 1.1. Use the formula from Step 1 to calculate excavator productivity. For instance, if the capacity of each rotor bucket is 10 cubic feet, the wheel has only one bucket, the rotor rotates at a speed of 5 rotations per minute, and the filling factor and the soil loosening factor are one, the productivity of the excavator stands at: Q = (60*q*z*n*kf) / kl = (60*10*1*5*1) / 1 = 3,000 cubic feet per hour. kf stands for the filling factor of a bucket while kl represents the soil-loosening factor.
If an excavator bucket is 75 inches wide 55 inches high and 83 inches deep how many cubic yards is the bucket volume?
7.34 cu yds.
How much concrete mix use in 5 cubic meter 1 bucket cement 4 bucket sand 8 bucket 40mm metal?
To calculate the total concrete mix for 5 cubic meters with the specified ratio of 1 bucket of cement, 4 buckets of sand, and 8 buckets of 40mm metal, first determine the total parts: 1 + 4 + 8 = 13 parts. For 5 cubic meters, each part would be approximately 0.385 cubic meters (5 / 13). Therefore, you would need about 0.385 cubic meters of cement, 1.54 cubic meters of sand, and 3.08 cubic meters of 40mm metal. Adjust bucket sizes accordingly to match these volumes based on the bucket's capacity.
How to calculate cubic meter of a triangle?
That is not possible. A triangle is an area. Cubic meters belong to volume or capacity.
Cubic inches in 5 gallon bucket?
A 5-gallon bucket filled with water contains 0.668 cubic feet of water.
How do you calculate the capacity of a cone?
Capacity or volume of a cone = 1/3*pi*radius2*height measured in cubic units
How many cubic feet are in a 12 X 14 foot room?
You need to include the third dimension to calculate the cubic capacity of a room
Calculate the cubic capacity of a freezer?
Take the three dimensions. Length, width and depth. Multiply them together L x W x D This will give you the cubic capacity in the units uses. ie cubic feet, meters etc.
A skid loader bucket holds how much sand in cubic feet or pounds?
The capacity of a skid loader bucket can vary depending on its size and manufacturer. A typical skid loader bucket can hold anywhere from 11 to 22 cubic feet of sand, which translates to roughly 800 to 1600 pounds of sand.
What equipment was included into the air forces ADR inventory?
4 Cubic Yard Front-End Loader, 8 Cubic Yard Dump Truck, Hydraulic Excavator
How do you calculate cubic capacity of an irregular volume?
You have to eat some hot-cheetos then poop them out and eat them again.
What would be the capacity of a fish tank?
To calculate capacity, you need the length, height, and width of your tank
