answersLogoWhite

0

A full adder is a logic circuit that take two inputs and a carry input, and produces an output and a carry ouput. It is one stage in a multi-bit adder. The truth table is: ABC RC D

000 00 0

001 10 1

010 10 2

011 01 3

100 10 4

101 01 5

110 01 6

111 11 7

The columns are A, B, Carry Input, Result, Carry Output, and Decoder Output You can use a 3 to 8 decoder to generate these 8 lines. Look at the R and C outputs, and note that there are 4 combinations of inputs thet generate a 1 or a 0. For each of Result and Carry Ouput, connect the decoder output representing the 0 state to those four lines. (Result = 0, 3, 5, 6. Carry Output = 0, 1, 2, 4) What you are doing logically is or'ing the lines to produce the 1's. Since you have nands instead or ors, treat the nands as nors and pick the opposite inputs.

User Avatar

Wiki User

16y ago

What else can I help you with?

Continue Learning about Engineering

Design a full adder using decoder and other sutiable gate?

give pin number 7, 11, 13, 14 to a 4input nand gate. this is the sum.give pin number 7, 9, 10, 12 to another 4input nand gate.this is the carry...


Why we use half adder even when full adder is more usefull?

A half adder has less components, and may therefore be cheaper. So, in cases where all you need is a half adder, it may be more convenient to use a half adder. Or it may be more convenient to mass-produce only the full adders, since a full adder can work as a half-adder as well.Also, in introductory electronics textbooks, the half-adder would be introduced first, just because it is simpler.


How do you perform Parallel Adder Addition?

A binary parallel adder is a digital function that produces arithmetic sum of two binary numbers in parallel. It consists of full-adder combinational arrangement thus, the output carry from one full adder connected to the input carry of next full- adder.


Advantages of fast adder over parallel binary adder?

serial adder: 1) Slower 2) It uses shift registers 3) IT requires one full adder circuit. 4) It is sequential circuit. 5) Time required for addition depends on number of bits. Parallel adder: 1) Faster 2) It uses registers with parallel load capacity 3) No. of full adder circuit is equal to no. of bits in binary adder. 4)It is a combinational circuit 5)Time required does not depend on the number of bits


What are the advantages of half and full adder circuit?

Do you mean :- how to get full adders by using half-adders? For this question refer following answer - A full-adder can be obtained by combining two half-adders and one or gate. Details on full-adder and half-adder can be referenced from following link http://www.fullchipdesign.com/fulladder.htm

Related Questions

Explain Implementation of full adder with a decoder?

A full adder can be implemented using a decoder by utilizing a 3-to-8 line decoder to decode the three input bits: A, B, and Carry-in (Cin). The decoder generates eight output lines corresponding to all possible combinations of the three inputs. The outputs of the decoder can then be combined with logic gates to derive the Sum and Carry-out outputs of the full adder. Specifically, the Sum output can be generated by ORing the appropriate outputs of the decoder, and the Carry-out can be derived from a combination of specific outputs as well.


Logic circuit forplementation of a full adder using decoder and 2 or gate?

Logic circuit forplementation of a full adder using decoder and 2 or gate? Read more:Logic_circuit_forplementation_of_a_full_adder_using_decoder_and_2_or_gate


Implement a full adder using a decoder?

A full adder can be implemented using a 3-to-8 decoder by using the sum and carry outputs of the adder as the decoder's outputs. Connect the three inputs (A, B, and Cin) to the decoder, which will activate one of its eight outputs based on the binary combination of these inputs. The sum output can be obtained by combining the appropriate activated outputs with XOR gates, while the carry output can be derived using OR gates to combine specific activated outputs. This setup allows the decoder to effectively represent the logic required for a full adder.


Why full adder is better then half adder?

Full adder is better than half adder because in half adder we can perform operation on only two digits and in full adder we can perform operation on three binary digits.


Difference between adder and parallel adder?

1.serial adder add bits serially but parallel adder add bits at the same time . 2.serial adder depends on previous outputs but parallel adder does not depends on previous outputs . 3.parallel adder takes less time to execute compared to serial adder.


Is a adder a reptile?

The adder is a snake, and snakes are reptiles.


What is a baby desert death adder called?

adder


What a puff adders common name?

The common name for a puff adder is simply "puff adder."


How can you the word adder in a sentence?

The adder is a poisonous snake. Using binary numbers, the adder produced a mathematical outcome.


What is ripple carry output?

Each full adder inputs a Cin, which is the Cout of the previous adder. This kind of adder is a ripple carry adder. Al-firoz hossainCE-07002MBSTU.Bangladesh.


Design a full adder using decoder and other sutiable gate?

give pin number 7, 11, 13, 14 to a 4input nand gate. this is the sum.give pin number 7, 9, 10, 12 to another 4input nand gate.this is the carry...


What are the different types of adders?

parallel adder,serial adder