answersLogoWhite

0

you can use a fuse or circuit breaker

User Avatar

Wiki User

15y ago

What else can I help you with?

Continue Learning about Engineering

Which can prevent a circuit from overloading?

In most appliances the single thing that prevents an overload is the fuse. In modern electronics there are various devices that can be used for power management which can limit the current drawn by reducing the load voltage. see: http://en.wikipedia.org/wiki/Current_limiting


What is designed to open an overloaded circuit and prevent overheating?

A circuit breaker or a fuse.


What is the purpose of the diode in the GM AC clutch circuit?

The purpose of the diode is to prevent electricity to flow in the wrong direction in a circuit. The purpose of the diode is to prevent electricity to flow in the wrong direction in a circuit.


Why is it that a voltmeter is not connected parallel in a circuit?

An ammeter is connected in series with the circuit being measured because you want to measure the current flowing through the circuit, whereas a voltmeter is connected in parallel with the circuit being measured because you want to measure the voltage across the circuit. Kirchoff's current law states that the signed sum of the currents entering a node is zero. A consequence of that law is that the current at every point is a series circuit is the same. The ammeter measures that current and, so long as its impedance is not too high, it won't disturb the circuit being measured. Kirchoff's voltage law, on the other hand, states that the signed sum of the voltage drops in a series circuit adds up to zero. A consequence of that law is that the voltage across parallel nodes must be equal. The voltmeter measures that voltage and, so long as it impedance is not too low, it won't disturb the circuit being measured. Formalities aside... An ammeter is a low impedance device. If you were to connect it in parallel with a circuit, it would draw all of the available current from that circuit. It and the circuit or its power supply would be damaged, because the ammeter represents a short circuit. A voltmeter is a high impedance device. If you were to connect it in series with a circuit, it would prevent any of the available current from reaching that circuit. While it and the circuit would probably not be damaged, the circuit would not function. Since practical meters are not perfect, the ammeter is not zero ohms impedance, nor is the voltmeter infinity ohms impedance. If you intend to measure both current and voltage in a circuit, it is normal protocol to measure the voltage across the circuit downstream of the ammeter, so that you would not be also measuring the additional voltage drop across the ammeter.


What is a component included in a circuit and designed to prevent too much current from flowing through the circuit?

A fuse.

Related Questions

Can I safely install a 20A outlet on a 15A circuit?

No, it is not safe to install a 20A outlet on a 15A circuit. The outlet should match the circuit's amperage to prevent overloading and potential fire hazards.


Can I safely install a 20 amp receptacle on a 15 amp circuit?

No, it is not safe to install a 20 amp receptacle on a 15 amp circuit. The receptacle should match the circuit's amp rating to prevent overloading and potential fire hazards.


The role of the circuit breaker is what?

to prevent a circuit from overloading if too much current flow safely interrupt the circuit if it becomes overloaded


A circuit with a separate path for each appliance is a?

dedicated circuit. It provides individual power supply to each appliance to ensure they receive a consistent and uninterrupted flow of electricity, which helps prevent overloading and ensures optimal performance.


Can you tie into your kitchen run to get your 240V to a receptacle?

No, tying into a kitchen run to power a 240V receptacle is not recommended. It's best to install a dedicated circuit for the receptacle and ensure that the wiring and circuit breaker are appropriately sized to handle the load. This will help prevent overloading the circuit and ensure safety.


How can I safely install electricity in a shed?

To safely install electricity in a shed, hire a licensed electrician to plan and complete the wiring. Ensure the shed has proper grounding, use outdoor-rated wiring and outlets, and install a circuit breaker to prevent overloading. Follow all local building codes and safety guidelines to prevent electrical hazards.


What can cause a circuit breaker to trip and how can it be prevented?

A circuit breaker can trip due to overloading, short circuits, or ground faults. To prevent tripping, avoid overloading circuits, regularly check for faulty wiring, and use surge protectors.


Does a fridge need a dedicated circuit for proper electrical operation?

Yes, a fridge typically requires a dedicated circuit to ensure proper electrical operation and prevent overloading the circuit.


Which electric safety device easily melts whe there is overheating or overloading in the circuit?

A fuse is an electric safety device that easily melts in response to overheating or overloading in the circuit. When a fuse melts, it breaks the circuit and cuts off the power supply to prevent further damage or risk of fire.


How does a fuse work to protect electrical circuits from overloading?

A fuse works by breaking the circuit when there is too much current flowing through it, which helps prevent damage to the electrical components from overheating or overloading.


Does a refrigerator need its own circuit in a household electrical system?

Yes, a refrigerator typically requires its own dedicated circuit in a household electrical system to ensure it has enough power and to prevent overloading the circuit.


Does a refrigerator need its own circuit for proper functioning?

Yes, a refrigerator typically requires its own dedicated circuit to ensure proper functioning and to prevent overloading the electrical system.